Robotis DYNAMIXEL XM430-W210 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 34

background image

2/22/2018

ROBOTIS e-Manual

http://emanual.robotis.com/docs/en/dxl/x/xm430-w210/

14/34

This value indicates maximum current(torque) output limit.
Goal Current(102) can’t be configured with any values
exceeding Current Limit(38). The Current Limit(38) is used in
Torque Control Mode and Current-based Position Control
Mode, therefore decreasing Current Limit(38) will result in
decreasing torque of DYNAMIXEL. For more details, please
refer to the Position PID Gain(80 ~ 84).

Unit

Value Range

about 2.69[mA]

0 ~ 1,193

Note

Current Limit(38) could be differ by each DYNAMIXEL so

please check the Control Table.

2. 4. 16. Acceleration Limit(40)

This value indicates maximum Profile Acceleration(108). Profile
Acceleration(108) can’t be configured with any values
exceeding Acceleration Limit(40). Profile Acceleration(108) is
used in all operating mode except PWM Control Mode in
order to generate a target trajectory. For more details, please
refer to the Profile Velocity(112).

Unit

Value Range

214.577 Rev/min

2

0 ~ 32,767

Note

Bit information of the Error field in the Status Packet is

different from protocol 1.0 and protocol 2.0. This manual
complies with protocol 2.0. Please refer to the

of e-Manual for more details about the protocol.

2. 4. 17. Velocity Limit(44)

This value indicates maximum velocity of Goal Velocity(104)
and Profile Velocity(112). For more details, please refer to the
Profile Velocity(112).

Unit

Value Range

0.229rpm

0 ~ 1,023

2. 4. 18. Min/Max Position Limit(48, 52)

These values limit maximum and minimum target positions for
Position Control Mode(Joint Mode) within the range of 1
rotation(0 ~ 4,095). Therefore, Goal Position(116) should be
configured within the position limit range. These values are
not used in Extended Position Control Mode and Current-
based Position Control Mode.

Back to Top ▲

«
...
12
13
14
15
16
...
»

Содержание DYNAMIXEL XM430-W210



































Отзывы:

Нет отзывов

Похожие инструкции для DYNAMIXEL XM430-W210

Бренд: Landoll Страницы: 52

Бренд: JBSYSTEMS Light Страницы: 14

Бренд: Ecco Страницы: 4

Бренд: JD Squared Страницы: 15

Бренд: DAPAudio Страницы: 16

Бренд: 3M Страницы: 28

Бренд: lancer Страницы: 12

Бренд: Dairyland Страницы: 21

Бренд: Baileigh Industrial Страницы: 40

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Бренд: Haki Страницы: 24

Бренд: Dakota Digital Страницы: 5

Бренд: Ocean Sonics Страницы: 45

Бренд: ZOLL Страницы: 37

Бренд: Wacker Neuson Страницы: 34

Бренд: Wagan Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды