background image

 
 

 

ENG

 

TECHNICAL INFORMATION 

 

24

 

 

 

3.  TECHNICAL INFORMATION  

3.1.  MACHINE GENERAL DESCRIPTION  

 

-

 

The machine is a semi-automatic machine for palletised load wrapping and stabilising with stretch film. 

-

 

The machine must be used only for wrapping and stabilising products contained in packages (in boxes, liquid 

containers, etc.) with regular shape or with a shape that ensures a stable palletisation. 

-

 

Packages containing liquids or insubstantial materials must have characteristics suitable to the product and be 

perfectly closed and sealed to prevent the contents from flowing out. 

-

 

The machine consists of a rotary table, which makes the pallet turn, and a spool carriage which unwinds and 

stretches the film. 

-

 

The machine is equipped with a series of safety devices designed to avoid any injuries to the operator or other 

persons using the machine. It comes in different models to satisfy different market needs. 

-

 

Stretch film spools commonly available on the market are used for load wrapping. 

-

 

This  machine  is  normally  installed  in  workshops  or  industrial  environments  protected  from  the  atmospheric 

agents. 

 

 

Danger - warning 

Using this machine in explosive environments or when exposed to atmospheric agents is strictly forbidden. 

 

-

 

The pallet loading and unloading are performed by the user, who can also insert and cut the film. 

-

 

Only one operator is required for its use. 

 

 

Содержание Masterplat FREEZER




























































































































Отзывы: