Robopac Masterplat FREEZER страница 12 Скачать руководство пользователя

Страница: 12 / 123

ENG

GENERAL INFORMATION

1.4. HOW TO REQUEST ASSISTANCE

Robopac distribution network is at your disposal for any problem regarding technical assistance, spare parts and any

new requirement you might need for your business.

For every technical service request regarding the machine, please indicate the data found on the identification plate,

the approximate hours of use and the type of fault detected.

Please refer to one of the authorised service centres or directly to the address indicated for any need.

ROBOPAC S.p.A

VIA FABRIZIO DA MONTEBELLO, 81

47892 GUALDICCIOLO REPUBLIC OF S. MARINO (RSM)

Tel. 0549 (interna+378) 910511

Fax 0549/908549 - 905946

htpp://www.aetnagroup.com

1.5. ATTACHED DOCUMENTATION

The machine is provided with the documentation listed below, unless otherwise agreed.

EC DECLARATION OF CONFORMITY.

Warranty conditions.

Pneumatic diagram.

Wiring diagram and list of components.

Manuals of installed commercial devices (if necessary for machine use).

Unpacking and installation instructions.

Quick guide for quick start.

USB pendrive containing the information listed below.

•

Use and maintenance manual translated into various languages

•

Spare parts catalogue.

•

Machine programming software.

•

Wiring Diagrams.

1.6. HOW TO READ THE INSTRUCTIONS FOR USE

The manual is divided into chapters, each of which describes a specific category of information.

Important

Every operator who interacts with the machine, in addition to reading all the documentation, must read

and learn the information that falls within his/her operational competence.

Refer to the abbreviation that precedes the title of the chapters in the index, to search for topics to consult.

These instructions are the result of an automatic system that assembles text and illustrations, so it is possible that

when changing pages, there might be interruptions in the flow of text and tables.

Important

Keep this manual for the entire duration of the machine useful life in a well known and easy to access

place, available for reference any time the need should arise.

Содержание Masterplat FREEZER




























































































































Результаты поиска

Содержание Masterplat FREEZER

Отзывы:

Похожие инструкции для Masterplat FREEZER

Бренды по названию

Популярные бренды

Robopac Masterplat FREEZER, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Masterplat FREEZER

Отзывы:

Похожие инструкции для Masterplat FREEZER

Бренды по названию

Популярные бренды