Robomow RC304 Pro Скачать руководство пользователя страница 62

Страница: 62 / 79

Setting

Description

P004*

Max Near-Wire Follow Distance

Maximal allowed distance from the edge, when P003 is On.

P005*

Min Near-Wire Follow Distance

Minimal allowed distance from the edge, when P003 is On.

P006*

Near Wire Follow Test

Test the mower at the max distance set in P004

P007

Rain Sensor On/Off

Automatically halt operation in rainy weather.

P008

Rain Sensor Sensitivity

Set higher value for higher sensitivity to rain.

P009

Edging On/Off

Enable/disable automatic edge-mowing.

P010

Child Lock On/Off

Lock the keypad to prevent accidental press.

See section 5 further.

P011

Anti-Theft On/Off

Enable and set a 4-digit PIN-code for protection.

See section 5 below.

P012

Anti-Theft PIN-code

Change and confirm new anti-theft PIN code.

See section 5 below.

P013

Base Station On/Off

Set an additional base for a separated zone.

P014

Add Separated Zone

Define a new separated zone and set its area size.

P015

Remove Zone

Delete a separated zone or a sub-zone.

P016

Sound On/Off

Disable operating sounds.

(*) This setting is not applicable to models for lawns under 800 m

/8600 ft

Содержание RC304 Pro
















































































Результаты поиска

Содержание RC304 Pro

Отзывы:

Похожие инструкции для RC304 Pro

Бренды по названию

Популярные бренды

Robomow RC304 Pro, Руководство пользователя

Результаты поиска

Содержание RC304 Pro

Отзывы:

Похожие инструкции для RC304 Pro

Бренды по названию

Популярные бренды