Roberts Gorden DF Скачать руководство пользователя страница 1

Страница: 1 / 74

WARNING

FOR YOUR SAFETY

If you smell gas:

1.  Open windows.
  2.  DO NOT try to light any appliance.
  3.  DO NOT use electrical switches.
  4.  DO NOT use any telephone in

your building.

  5.  Extinguish any open flame.
  6.  Leave the building.
  7.  Immediately call your local gas

supplier after leaving the building.

Follow the gas supplier’s

instructions.

8. If you cannot reach your gas

supplier, call the Fire Department.

Fire Hazard

Keep all flammable objects, liquids and
vapors the minimum required clear-
ances to combustibles away from
heater.

Some objects will catch fire or explode
when placed close to heater.

Failure to follow these instructions can
result in death, injury or property
damage.

WARNING

Installation must be done by a contractor qualified
in the installation and service of gas-fired heating
equipment or your gas supplier.

Improper installation, adjustment, alteration, service
or maintenance can result in death, injury or
property damage. Read the Installation, Operation
and Service Manual thoroughly before installing or
servicing this equipment.

Installer

Please take the time to read and understand

these instructions prior to any installation.

Installer must give a copy of this manual to the owner.

Owner

Keep this manual in a safe place in order to provide

your service technician with necessary information.

Roberts-Gordon LLC

1250 William Street

Buffalo, New York 14240-0044

www.robertsgordon.com

P/N 173101NA Rev. P 10/22

Model DF

Gas-Fired, Low Intensity

Two Stage Unitary Heater

Installation, Operation &

Service Manual

DF-80

DF-100

DF-125
DF-150
DF-175

DF-200

Содержание DF











































































Результаты поиска

Содержание DF

Отзывы:

Бренды по названию

Популярные бренды

Roberts Gorden DF, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание DF

Отзывы:

Бренды по названию

Популярные бренды