Robe Robin 300E Spot Скачать руководство пользователя страница 7

Страница: 7 / 39

4.2 Installing the lamp

DANGER ! Install the lamp with the device switched off only.

Unplug from mains before !

To insert the new lamp.

1. Disconnect the fixture from power and allow it to cool

at least 5 minutes.

2. Make sure that the fixture´s head is in the position as

shown on the picture (notices on the lamp cover are in

readable position) .Loosen the two quarter-turn

fasteners (1) marked “X,Y“ on the lamp cover to

open this cover.

3. Holding the lamp by its ceramic base, carefully

turn the lamp

to the left to loosen the lamp from

the lamp holder.

Gently pull the lamp out of the lamp holder

4. Holding the new lamp by its ceramics base, gently

insert the lamp to the lamp socket and turn the base

to the right.

Make sure that the lamp is installed tightly

into the lamp socket.

Do not install a lamp with a higher wattage! A lamp

like this generates temperatures the device is not

designed for. Damages caused by non-observance are not subject to warranty. Please follow the lamp

manufacturer‘s

notes! Do not touch the glass bulb bare hand during the

installation!

5. Re-insert the lamp cover and tighten the two quarter-turn

fasteners (1).

6. Switch on the fixture.

7. Align the lamp (see instructions below)

8. Reset the "Lamp On Time” and "Lamp Strikes” counters

in the menu "Information”.

Do not operate this fixture with open lamp cover!

4.3 Lamp adjustment

The lamp holder is aligned at the factory. Due to differences between lamps,the fine adjustment may improve

light performance:

To adjust the lamp in the fixture.

1. Switch on the fixture and after its reset turn on the

lamp.

2. Go to the "Service" menu and select the item "Adjust

Lamp" to project the light beam on the wall.

3. Use items in this menu to focus the light beam and set

the item HotSpot at 0 DMX .

Turn adjustment screws marked “A, B, C” (2) one after

another a quarter-turn clockwise until you reach a mechani

cal stop.

Center the hot-spot (the brightest part of the beam) using

these

3 adjustment screws (2).

5. Disconnect DMX from the fixture and go to the "Service"

menu and select the menu "Calibrations" and enter menu

"Calibrate Effects" and select item "HotSpot". Use this item

to adjust max. light intensity. After having adjusted the max.

light intensity, save this value by touching the [confirm] icon

and leave the "Calibrate Effects" menu by touching the

[confirm] again.

Содержание Robin 300E Spot








































Результаты поиска

Содержание Robin 300E Spot

Отзывы:

Похожие инструкции для Robin 300E Spot

Бренды по названию

Популярные бренды

Robe Robin 300E Spot, Руководство пользователя

Результаты поиска

Содержание Robin 300E Spot

Отзывы:

Похожие инструкции для Robin 300E Spot

Бренды по названию

Популярные бренды