ROBB Smarrt Rgbw Led Strip Скачать руководство пользователя страница 2

Страница: 2 / 2

8. Find and Bind Mode

Step 1

: Reset power of the device (initiator node) 3 times to start Find and Bind mode (connected light flashes

slowly) to find and bind target node, 180 seconds timeout, repeat this step.

Step 2

: Set the remote or touch panel (target node) into find and bind mode, and enable it

to find and bind initiator, please refer to corresponding remote or touch panel manual

Step 3

: There shall be indication on the remote or touch panel that it bind the device

successfully and can control it then

7. Factory Reset

through

Zigbee

Remote (Touch Reset)

Step 1

: Reset power of the device to start TouchLink Commissioning, 180 seconds timeout, repeat this step.

Note

: Make sure the device already added to a network, the remote added to the same one or not added to any network.

Zigbee

Remote

9. Learning to a Zigbee Green Power Switch

Step 2:

Set the green power switch into

Learning mode, please refer to its manual

Zigbee

Green Power

Switch

Step 3

: Connected light will flash twice

to indicate successful learning. Then
the switch can control the device.

Step 1

: Reset power of the device 4 times to start Learning mode to GP switch (connected light flashes twice), 180

seconds timeout, repeat this step.

Note: Each device can learn to
max. 20 zigbee green power switches.

11. Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)

Zigbee

Remote

< 10cm TouchLink

Step 2

: Set another device or remote or touch panel into network pairing

mode and pair to the network, refer to their manuals

Step 3

: Pair more devices and remotes to the network as you would like,

refer to their manuals.

Step 4

: Bind the added devices and remotes through Touchlink so that the

devices can be controlled by the remotes, refer to their manuals.

Step 1

: Reset power of the device 4 times to enable the device to setup a zigbee network (connected light flashes twice)

to discover and add other devices, 180 seconds timeout, repeat this step.

Zigbee Lighting Device

Input Clusters

•

0x0000: Basic

•

0x0003: Identify

•

0x0004: Groups

•

0x0005: Scenes

•

0x0006: On/off

•

0x0008: Level Control

•

0x0300: Color Control

•

0x0b05: Diagnostics

Output Clusters

•

0x0019: OTA

12. ZigBee Clusters the device supports are as follows:

Note: 1) Each added device can link and be controlled by max. 30 added remotes.
2) Each added remote can link and control max. 30 added devices.

13. OTA

The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every
10 minutes automatically.

Note: 1) If the device is already at factory default setting, there is no indication when factory reset again .
2) All configuration parameters will be reset after the device is reset or removed from the network.

Step 1

: Reset power of the device for 5 times continuously.

Step 2

: Connected light will blink 3 times

to indicate successful reset.

6. Factory Reset Manually

Step 2:

Set the paired green power switch into Learning mode, please refer to its manual

Zigbee

Green Power

Switch

Step 3

: Connected light will flash 4

times to indicate successful deleting.

Step 1

: Reset power of the device 3 times to start delete Learning mode to GP switch (connected light flashes slowly), 180

seconds timeout, repeat the operation.

10. Delete Learning to a Zigbee Green Power Switch

< 10cm

Zigbee Remote

Step 2

: Bring the remote or touch

panel within 10cm of the lighting
device.

Step 3

: Set the remote or touch panel into Touch Reset procedure to reset the

device, please refer to corresponding remote or touch panel manual to learn how.

Step 4

: There shall

be indication on the
remote and
connected light
flashes 3 times for
successful reset.

AC Power

50/60Hz