RMS R325I Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 26

RMS R325I Скачать руководство пользователя страница 2

RMS Technologies

Page 2

Version 1.20

R325I Single Axis Controller/Driver Manual

02/13/2006

Thank you for purchasing the R325I Single-Axis Controller/Driver. This product is
warranted to be free of manufacturing defects for one (1) year from the date of

purchase.

PLEASE READ BEFORE USING

Before you start, you must have a suitable step motor, a DC power supply suitable
for the motor and a current resistor. The power supply voltage must be between 4

times and 20 times the motor's rated voltage.

DISCLAIMER

The information provided in this document is believed to be reliable. However, no

responsibility is assumed for any possible inaccuracies or omissions. Specifications
are subject to change without notice.

RMS Technologies reserves the right to make changes without further notice to any

products herein to improve reliability, function, or design. RMS Technologies does
not assume any liability arising out of the application or use of any product or circuit
described herein; neither does it convey any license under its patent rights, nor the

rights of others

Note: This equipment has been tested and found to comply with the limits for a

Class (A) digital device, pursuant to part 15 of the FCC Rules. These Limits are
designed to provide reasonable protection against harmful interferences when the

equipment is operated in its installation. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. If this

equipment does cause harmful interference the user will be required to correct the
interference.

This Class (A) digital apparatus complies with Canadian ICES-003

Cet appareil numérique de la classe (A) est conforme à la norme NMB-003 du Canada

Special Symbols

Indicates a WARNING and that this information could prevent

injury, loss of property, or even death (in extreme cases).

«
1
2
3
4
...
»

Содержание R325I



























Отзывы:

Нет отзывов