RMS 1S25 Series Скачать руководство пользователя страница 4

Страница: 4 / 10

Visit

www.rmspl.com.au

for the latest product information.

Due to RMS continuous product improvement policy this information is subject to change without notice. 1S25/Issue F/07/03/2011 - 4/9

ZONE 1

ARC PROTECTION

COMMON

ALARM

OUTPUT

1S25

50/51

HEALTH Y

Z ONE 2

Z ONE 3

Z ONE 4

Z ONE 1

Cus tom te xt

FAIL

T RIP

RESET

/T EST

TRIP

Figure 6:

Up to eight arc sensors distributed in low voltage switchgear.

Over current check stage depicted.

Low Voltage Applications

LOW VOLTAGE ARC PROTECTION

Figures 6 & 7 depict how the 1S25 may also be applied for low

voltage panels & MCC switchgear.
Figure 6 depicts an arrangement where over current check stage

is employed while the protection application depicted in figure 7

is a system based solely on arc detection.

1S25

HEALTH Y

Z ONE 2

Z ONE 3

Z ONE 4

Z ONE 1

Cus tom te xt

FAIL

T RIP

RESET

/T EST

COMMON

TRIP

ALARM

OUTPUTS

Figure 7:

Up to eight arc sensors distributed in low voltage switchgear or

MCC compartments without over current check

Содержание 1S25 Series











Результаты поиска

Содержание 1S25 Series

Отзывы:

Бренды по названию

Популярные бренды

RMS 1S25 Series, Технический бюллетень

Результаты поиска

Содержание 1S25 Series

Отзывы:

Бренды по названию

Популярные бренды