background image

 
 

 

Bedienungsanleitung TCO

4

 

 

4. Technical Specifications 

 

4.1 TCO-FF 

 
LTC/Video In 

• 

LTC In: BNC, unbalanced 

• 

Level range LTC In: -25 dBu up to +12 dBu 

 

• 

Video In: BNC unbalanced, switchable termination 75 Ohm 

• 

Format: PAL and NTSC 

 

LTC Out 

• 

BNC 

• 

Output level: +4 dBu, via jumper –7 dBu 

• 

Output impedance: 220 Ohm 

 

• 

Power supply via ribbon cable, 5 V DC, 100 mA

 

• 

Dimensions (WxD): 100 x 75 mm 

 
 

4.2 TCO-HDSP 

 

LTC In 

• 

BNC, unbalanced 

• 

Level range: -25 dBu up to +12 dBu 

 

Video In (Word Clock In) 

• 

BNC, switchable termination 75 Ohm 

• 

Format: PAL and NTSC 

 

Word Clock In (Video In) 

• 

BNC, switchable termination 75 Ohm 

• 

Transformer coupled, galvanically isolated input 

• 

Not affected by DC-offsets within the network 

• 

Signal Adaptation Circuit: signal refresh through auto-center and hysteresis 

• 

Overvoltage protection 

• 

Level range: 1.0 Vpp – 5.6 Vpp 

• 

Lock Range: 28 kHz – 200 kHz 

• 

Jitter when synced to input signal: < 1 ns 

• 

Jitter suppression: > 30 dB (2.4 kHz) 

 

LTC Out 

• 

BNC 

• 

Output level: +4 dBu, via jumper –7 dBu 

• 

Output impedance: 220 Ohm 

 

Word Clock Out 

• 

BNC 

• 

Max. output voltage: 5 Vpp 

• 

Output voltage @ 75 Ohm termination: 4.0 Vpp 

• 

Output impedance: 10 Ohm 

• 

Frequency range: 28 kHz – 52 kHz 

 

• 

Power supply via ribbon cable, 5 V DC, 100 mA

 

• 

Standard bracket, dimensions PCB (WxD): 98 x 75 mm 

 

Содержание TCO FF













Отзывы: