RLE Technologies WiNG-MGR Скачать руководство пользователя страница 22

Страница: 22 / 102

WiNG-MGR User Guide

800.815.1519

Getting Started

2.4.2 Set the IP Address via EIA-232 Connection

To use the EIA-232 interface:

Contact your IT Department to obtain an available IP address, Subnet Mask, and default

Gateway.

Use a 9-pin male-female straight through serial cable to connect the EIA-232 port on the

WiNG-MGR to a terminal or PC running terminal emulation software (HyperTerminal).

Set the appropriate communication port to

9600 baud

NO parity

8 data bits

1 stop bit

(9600/N/8/1)

, and

no software or hardware flow command

Once the terminal emulation software starts, press

Enter

on the keyboard and the

WiNG-MGR boot prompt should appear, (MGR> or MGR boot>). If the boot prompt does

not appear, check the communication settings and make sure the unit is powered on.

From the boot prompt type

then type one space and type the IP address your IT

Department provided for the unit. If you’d like to enable DHCP, type 0.0.0.0 as the IP

address. Press the enter key. For example,

IP 192.168.103.211

The WiNG-MGR will

reboot after the IP address is changed.

From the boot prompt type

then type one space and type the Subnet Mask address your

IT Department provided for the unit. Press the enter key. For example,

NM 255.255.255.0

The WiNG-MGR will reboot after the Subnet Mask is changed.

From the boot prompt type

then type one space and type the Default Gateway address

your IT Department provided for the unit. Press the enter key. For example,

DG 192.168.103.1

The WiNG-MGR will reboot after the Default Gateway is changed.

The IP address is now set and the WiNG-MGR can be accessed through a Web browser

using the new IP address.

Содержание WiNG-MGR







































































































Результаты поиска

Содержание WiNG-MGR

Отзывы:

Бренды по названию

Популярные бренды

RLE Technologies WiNG-MGR, Руководство пользователя

Результаты поиска

Содержание WiNG-MGR

Отзывы:

Бренды по названию

Популярные бренды