manualshive.com logo in svg

RKI Instruments 65-2428, Руководство оператора, Страница: 17 / 18

Поделиться
Скачать
RKI Instruments 65-2428 Скачать руководство пользователя страница 17

 

12 • 65-2428 H

2

S Detector

NOTE:

If you do not allow the gas reading decrease below the alarm points, then 
unwanted alarms may occur.

2.

Verify that the controller display reading decreases and stabilizes at 0 ppm H

2

S.

3.

Store the components of the calibration kit in a safe and convenient place.

Parts List

Table 2 lists replacement parts and accessories for the H

2

S detector.

Table 2: Parts List

Part Number

Description

06-1248RK

Sample tubing (order by the foot)

07-0033RK

Detector housing cap gasket

07-0203RK

Rubber retaining boot

14-2101RK

Spacer between sensor and rubber boot

65-2428

H

2

S replacement detector assembly (includes sensor)

71-0344

65-2428 H

2

S Detector Operator’s Manual (this document)

81-0076RK

Zero air calibration cylinder, 17 liter steel

81-0076RK-01

Zero air calibration cylinder, 34 liter steel

81-0076RK-03

Zero air calibration cylinder, 103 liter steel

81-0151RK-02

Calibration gas cylinder, 25 ppm H

2

S in nitrogen, 58 liter aluminum

81-0151RK-04

Calibration cylinder (25 ppm H

2

S in nitrogen; 34 liter aluminum)

81-1050RK

Regulator with gauge and knob, 0.5 LPM, for 17 liter and 34 liter 
steel calibration cylinders

81-1051RK

Regulator with gauge and knob, 0.5 LPM, for 34AL/58/103 liter 
calibration cylinders)

81-1117RK

Calibration cup

ES-1537-H2S

H

2

S replacement sensor

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 65-2428



















Отзывы:

Нет отзывов