RKI Instruments 35-3001A-14 Скачать руководство пользователя

Страница: 24 / 24

20 • 35-3001A-14 Methane Sample-Draw Detector

Parts List

Table 4 lists replacement parts and accessories for the sample-draw detector.

Table 4: Parts List

Part Number

Description

06-1248RK

Sample tubing, 3/16” ID x 5/16” OD, specify length

06-1248RK-03

Sample tubing, 3/16” ID x 5/16” OD, 3 feet (for calibration kit)

07-0110RK

Gasket for IR flow block

17-2670

Inlet fitting O-ring

17-2671

Inlet fitting front ferrule

17-2672

Inlet fitting back ferrule and tube nut

30-1016RK

Pump

33-0164RK

Oil mist filter

33-0165RK

Hydrophobic filter

33-0167RK

Particle filter

61-5039RK-CH4

Infrared CH

sensor, plug-in type,

%vol

range

71-0603

Operator’s Manual, 35-3001A-14 Sample-Draw Detector

81-0012RK-01

Calibration cylinder, 50% LEL methane in air, 34 liter steel

81-0012RK-05

Calibration cylinder, 50% LEL methane in air, 58 liter

81-0076RK-01

Zero air calibration cylinder, 34 liter steel

81-0076RK-03

Zero air calibration cylinder, 103 liter

81-1054RK

Regulator, demand flow, for 34 liter aluminum, 58 liter, and 103 liter
calibration cylinders (cylinders with internal threads)

81-1055RK

Regulator, demand flow, for 17 liter and 34 liter steel calibration cylinders
(cylinders with external threads)

Содержание 35-3001A-14

























Результаты поиска

Содержание 35-3001A-14

Отзывы:

Похожие инструкции для 35-3001A-14

Бренды по названию

Популярные бренды

RKI Instruments 35-3001A-14, Руководство оператора

Результаты поиска

Содержание 35-3001A-14

Отзывы:

Похожие инструкции для 35-3001A-14

Бренды по названию

Популярные бренды