RKI Instruments 35-3001-13 Series Скачать руководство пользователя страница 24

Страница: 24 / 25

24 • 35-3001-13-02 Carbon Dioxide/Oxygen Sample-Draw Detector

Parts List

Table 2 lists replacement parts and accessories for the sample-draw detector.

Table 2: Parts List

Part Number

Description

06-1248RK

Sample tubing, 3/16” ID x 5/16” OD, specify length

06-1248RK-03

Sample tubing, 3/16” ID x 5/16” OD, 3 feet (for calibration kit)

07-0053RK

Gasket for oxygen flow block

07-0110RK

Gasket for IR flow block

17-2670

Inlet fitting O-ring

17-2671

Inlet fitting front ferrule

17-2672

Inlet fitting back ferrule and tube nut

30-1016RK

Pump

33-0165RK

Hydrophobic filter

33-0167RK

Particle filter

61-5040RK-02

Infrared carbon dioxide sensor, 0 - 5,000 ppm

range

61-5040RK-03

Infrared carbon dioxide sensor, 0 - 5% vol

range

61-5040RK-05

Infrared carbon dioxide sensor, 0 - 50% vol

range

61-5040RK-10

Infrared carbon dioxide sensor, 0 - 100% vol

range

71-0506

Operator’s Manual, 35-3001-13-XX Sample-Draw Detector

81-0070RK-01

Calibration cylinder, 2000 ppm CO

in nitrogen, 34 liter steel

81-0070RK-03

Calibration cylinder, 2000 ppm CO

in nitrogen, 103 liter

81-0072RK-01

Calibration cylinder, 2.5% CO

in nitrogen, 34 liter steel

81-0072RK-03

Calibration cylinder, 2.5% CO

in nitrogen, 103 liter

81-0073RK-01

Calibration cylinder, 15% CO

in nitrogen, 34 liter steel

81-0073RK-03

Calibration cylinder, 15% CO

in nitrogen, 103 liter

81-0076RK-01

Zero air calibration cylinder, 34 liter steel

81-0076RK-03

Zero air calibration cylinder, 103 liter

81-0078RK-01

Calibration cylinder, 100% nitrogen, 34 liter steel

81-0078RK-03

Calibration cylinder, 100% nitrogen, 103 liter

81-1054RK

Regulator, demand flow, for 34 liter aluminum, 58 liter, and 103 liter calibration
cylinders (cylinders with internal threads)

Содержание 35-3001-13 Series


























Результаты поиска

Содержание 35-3001-13 Series

Отзывы:

Похожие инструкции для 35-3001-13 Series

Бренды по названию

Популярные бренды

RKI Instruments 35-3001-13 Series, Руководство оператора

Результаты поиска

Содержание 35-3001-13 Series

Отзывы:

Похожие инструкции для 35-3001-13 Series

Бренды по названию

Популярные бренды