background image

34-500 09/07 

1

 

OPERATING INSTRUCTIONS 

 

EMBLEM

® 

GAS-FIRED MULTIPLE BOILER HEATING SYSTEM 

 

 

Installation and service must be performed by a qualified service installer, service agency or the gas supplier. 

 

THIS MANUAL CONTAINS INFORMATION REQUIRED FOR OPERATION AND MAINTENANCE OF THE EMBLEM

®

 

GAS-FIRED MULTIPLE BOILER HEATING SYSTEM. REFER TO INDIVIDUAL PRIMERA

®

 AND EPV

®

 BOILER 

INSTALLATION AND MAINTENANCE MANUALS FOR INSTRUCTIONS, WARNINGS AND IMPORTANT INFORMATION 
ABOUT THE INSTALLATION, OPERATION AND MAINTENANCE FOR EACH OF THE BOILERS IN THIS HEATING 
SYSTEM. READ AND FOLLOW ALL INSTRUCTIONS, MARKINGS AND WARNINGS BEFORE ATTEMPTING TO 
START AND OPERATE EITHER BOILER. 

 

 

 

TO THE INSTALLER:

  After installation, these instructions must be given to the equipment user or left near the appliance. 

Refer to I & M documents 34-50, 34-501 and 34-502 for additional important information. 

 
SPECIAL INSTRUCTIONS TO THE OWNER:

  Retain this manual for future reference.  These instructions contain 

important information that will help you in maintaining and operating this appliance. 
 

CHECKING EQUIPMENT BEFORE YOU INSTALL

 - Upon receiving equipment, check for signs of shipping damage. 

Inspect the appliance and all accompanying parts for signs of impact or mishandling. Verify the total number of pieces 
shown on packing slips with those actually received. If there is damage or a shortage, contact the carrier immediately. 
 

WARRANTY

 - Factory warranty does not cover improper installation or operation.  (See individual PRIMERA

®

 and EPV

®

 

boiler warranties for complete details).  

 

 

 
 
 
 
 
 
 
 

 

Riverside Hydronics

®

, LLC  -  990 Haltom Road  -  Fort Worth, Texas  76117  -  Tel 1-800-990-5918

 

Содержание Emblem











Отзывы: