Riverside Hydronics 1000 WBX 125A-IFC Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 42

Riverside Hydronics 1000 WBX 125A-IFC Скачать руководство пользователя страница 1

1

34-56 07/13

Centauri

®

CONDENSING

WATER

BOILER

INSTALLATION & MAINTENANCE MANUAL

Models (400, 500, 650, 750, 850, 900, 1000) WB 125A-IFC

Models (500, 650, 750, 850, 900, 1000) WB 250A-IFC

Installation and service must be performed by a qualified service installer, service agency or the gas supplier.

IMPORTANT: THIS MANUAL CONTAINS INFORMATION REQUIRED FOR INSTALLATION, OPERATION AND
MAINTENANCE OF THIS EQUIPMENT. READ AND FOLLOW THE INFORMATION IN THIS MANUAL AND ALL OTHER
PROVIDED INSTRUCTIONS, LABELS AND MARKINGS BEFORE INSTALLING, OPERATING OR SERVICING THIS
UNIT.

TO THE INSTALLER: After installation, these instructions must be given to the equipment user or left near the appliance.
SPECIAL INSTRUCTIONS TO THE OWNER: Retain this manual for future reference. These instructions contain important
information that will help you in maintaining and operating this appliance.

Riverside Hydronics

®

, LLC

990 Haltom Road
Fort Worth, Texas 76117
1-800-990-5918

www.riversidehydronics.com

1
2
3
...
»

Содержание 1000 WBX 125A-IFC











































Отзывы:

Нет отзывов