background image

Check for parts online at 

www.HuntRiversEdge.com

 or call 800-450-EDGE (3343) M-F 8-5

14

Operator's Manual

RELAX WIDE Ladder Stand

5.  a. Loop the D-loop end of the two 16' criss cross straps (30) 

through the loop end to form a cinch knot around the ladder 

rail tube. Secure beneath a step rung, at the stabilizer bar height 

location. SEE FIGURE 15A.
b. With the stand level and being held in place by two people, 

the third person must cross one of the 16' criss cross straps (30) 

behind the tree and feed the free end through the opposite 

D-loop. SEE FIGURE 15B-E.
c. Criss cross the other 16' stabilizer strap (30), forming an "X" 

pattern on the of the tree and feed the free end through the 

opposite D-loop. SEE FIGURE 15B-E.

6.  Make sure the criss cross straps and stabilizer bar strap are snug 

and the tree blade is still contacting the tree.

 

NOTE: This ground level ladder-to-tree attachment will prevent 

the ladder from pulling away from the tree while ascending to the 

top for final 6' ratchet strap (25) attachment. The same holds tree 

when the ladder is removed.  

7.  With two people securely holding the ladder, use the three point 

contact climbing method to slowly climb the ladder and carefully 

keep a constant hand grip on the ladder at all times. Always lean 

forward, toward tree, to keep top section tree blades against the 

tree.  Be certain ladder bottom is firmly seated on dry, level 

ground.  Attach your harness tether to the tree before securing 

the platform to the tree and stepping onto platform.  Refer to 

the Full Body Harness instructions included with this product.

 

NOTE: Bring ratchet strap up with you in a pocket. DO NOT carry 

in your hand!

8.  a. Standing on ladder step, lean toward tree with ratchet strap now 

in hand, Hook "S" hook with long strap through hole provided on 

tree blade. Feed the long strap through the center (slot) of ratcheting 

mechanism and back around through tightening lever. SEE FIGURES 

16, 17A AND 17B.

 

NOTE: Be sure you feed the long strap correctly so there are no twists in 

the strap.

 

b. Wrap entire ratchet assembly around tree and hook other "S" hook through 

opposite upper tree blade hole. Pull tail of long strap until most of the slack 

is taken out. Be sure entire strap is even and at the same level all around tree. 

"Ratchet" tight to tree, this will securely attach ladder to tree and prevent 

movement. SEE FIGURES 17C.

NOTE: Make sure there is at least two full revolutions of strap on the 

ratchet spool before the strap tightens.  Proper tension will ensure 

the stand is secured to the tree. Do not allow excessive strap to build 

up in the ratchet as this will prevent the ratchet teeth from engaging 

and can cause slippage.

 

To release ratchet, simply pull the release lever and open tightening 

lever wide open (flat). 

SEE FIGURE 17D.

9.  If necessary, re-check and adjust the 6' ratchet strap (25), 16' criss 

cross straps (30) and horizontal stabilizer bar assembly to  securely 

attach the treestand to the tree.  The tree blade must be touching the 

tree.

10.  You are now ready to use your ladder stand.

FIGURE 17A

FIGURE 17B

FIGURE 17C

FIGURE 17D

IMPORTANT

Reverse the Set-Up and Use Instructions to take the 

ladder stand down. 

FIGURE 16

Criss Cross 

Straps

Ratchet Strap

Содержание RELAX WIDE RE631





















Отзывы: