Rivers Edge Landmark LM600 Скачать руководство пользователя страница 18

Страница: 18 / 24

Check for parts online at

www.HuntRiversEdge.com

or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

Landmark

™

Permanent Blind

10. Wrap the edge corner flaps of the roof panel around the

eave corners of the frame assembly and secure with Velcro.

SEE FIGURE 18 A-B.

11. Pull the roof panel tight by wrapping D-ring straps around

eave frame. Feed the long strap through both D-rings and

back through to tighten. Refer back to FIGURE 16 for strap

routing.

12. Insert three S1 poles (window rails) into the sewn sleeves

found on the lower window panels. You will use one tube

per panel. This makes these window panels the lower

window panels and the metal tube will act as shooting rest.

SEE FIGURE 19.

13. Attach the upper and lower window panels by pressing

the sewn on C-clips to the metal window supports that

were slid into the sewn on sleeves of the back and side wall

panels. SEE FIGURE 20.

14. Attach the upper and lower door panels by pressing the

sewn on C-clips to the metal window supports that were

slid into the sewn on sleeves of the right and left front side

wall panels. SEE FIGURE 20.

15. Ground stakes should be placed about one foot on either

side of each corner such that the top of the ground stakes

loop over the A1 and B1 poles and pin them to the ground.

There should be two ground stakes per side.

FIGURE 18

FIGURE 19

Lower

Window

Panel

Upper

Window

Panel

Sewn

Sleeve

FIGURE 20

Содержание Landmark LM600
























Результаты поиска

Содержание Landmark LM600

Отзывы:

Похожие инструкции для Landmark LM600

Бренды по названию

Популярные бренды

Rivers Edge Landmark LM600, Руководство оператора

Результаты поиска

Содержание Landmark LM600

Отзывы:

Похожие инструкции для Landmark LM600

Бренды по названию

Популярные бренды