manualshive.com logo in svg

Rivera 9000-0011-0037, Руководство пользователя

Поделиться
Скачать
Rivera 9000-0011-0037 Скачать руководство пользователя страница 9

rhythm accompaniment sounds are usually equalized for bottom and top-end tones with a decreased 
midrange.  Using an instrument with midrange-rich pickups such as dual-coil hum buckers may 
require far more “cut” than a similar instrument equipped with single-coil pickups. Selecting a 
humbucking pickup equipped semi-acoustic guitars neck-position pickup provides a very bass-
heavy and fat tone that may be too “dark,” but by experimenting with different settings, you can 
dial in a much more pleasant rhythm sound. 

Standby 

By turning the Power on and the Standby off (the down position, labeled with a 

“0”), you can warm up the amplifier before applying full voltage to the preamp and power 
output tubes. This prolongs tube life. Using the Standby switch when you’re taking a break 
also helps to extend the tubes’ life, plus it keeps the amp constantly at the ready. Just flip the 
Standby switch to the up (“I”) position, and you’re ready to play. 

Power 

This is your main power switch. The on position is indicated by the light being 

illuminated. The off position is marked by the “0” on the switch. Before turning the amp on, always 
check that a speaker is connected and that the power cord is firmly plugged into the amp and the 
outlet. 

 

R 

E A R 

P

A N E L 

Mains Input 

Your Sedona has a detachable power cord that connects to the chassis AC connector labeled Mains 
Input. Always use this cord and, in the event that the power cord requires replacement, replace it 
with the same type of power cord. 
Consult your RIVERA dealer for further information. Be sure to use a grounded electrical mains 
power supply socket whenever possible. These outlets have a grounding pin in addition to the 
normal line and neutral pin. The power cord supplied with your Sedona has a 3-pin plug. Do not cut 
off or damage the ground pin. If the available electrical outlet is of the older 2-pin type, use a 
suitable ground-lift adapter.  The U.S.A., Canada, and Japan share a common CSA/UL-style cord. 
Most of Europe and Scandinavia utilize a Euro plug and have a NEMKO/CE-style cord. Australia 
uses a different type of plug, as does England. 

Note: 

Avoid using long extension cords. Long cords have sufficient resistance to electrical current 

that the voltage arriving at your amp can be significantly reduced. This can have a bad effect on 
your tone. 

 
Mains Fuse 

 

This AC line fuse protects your amplifier from damage due to shorts, momentary surges, and 
defective power tubes. In the event of a fuse failure, always replace it with the same type of fuse. 

Содержание 9000-0011-0037




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды