Rival 4 Quart Wood Bucket, Руководство пользователя, Страница: 3 / 8

• MOTOR DRIVE
Top mounted. Engages stem of
DASHER and locks to bucket.
• COVER
Tab in COVER fits notch in ice
cream can.
• DASHER
Stem on top fits through hole in
center of COVER, and engages
MOTOR DRIVE.
• ICE CREAM CAN
Container holds ice cream mixture.
• DRAIN HOLE
Allows salt water to flow freely
out of BUCKET.
• WOODEN BUCKET
MOTOR DRIVE tabs secure
BUCKET. DRAIN HOLE located near top of BUCKET. Holds rock salt and ice.
KNOW YOUR ICE CREAM MAKER
-4-
-5-
HOW TO USE YOUR ICE CREAM MAKER
4. Pour chilled ice cream mixture into chilled ICE CREAM CAN. Do not fill
above the max level marked on the inside of the CAN.
5. Insert DASHER into ICE CREAM CAN. Then place COVER on ICE CREAM
CAN by lining up the stem on the DASHER with the hole on the COVER.
6. Carefully insert the ICE CREAM CAN with COVER into the center of
the BUCKET. Make sure ICE CREAM CAN engages with the bottom of
the BUCKET.
7. Carefully slide the rectangular tab (located on opposite end of power
switch) into the square bracket slot on BUCKET, align the MOTOR DRIVE
over ICE CREAM CAN so that the stem of the DASHER engages hole in
the bottom of the MOTOR DRIVE. Rotate ICE CREAM CAN slightly until
MOTOR DRIVE engages ICE CREAM CAN COVER. Lock in MOTOR DRIVE
into BUCKET with latching handle.
8. Plug Power cord into outlet.
9. Switch power to on and make sure the ICE CREAM CAN starts to
rotate. While ICE CREAM CAN is rotating, begin to distribute
approximately 2 inches of ice cubes around the inside bottom of the
BUCKET. Sprinkle approximately
1
/
4
cup of rock salt uniformly over
the layer of ice. (NOTE: The DASHER does not move, the ICE CREAM
CAN rotates around the DASHER.)
10. Continue to layer ice and then rock salt until level reaches top of
rotating ICE CREAM CAN. (NOTE: If CAN stops rotating - turn unit off -
manually turn the ICE CREAM CAN until it seems to turn smoothly - as
ice cubes might have jammed against the rotating ICE CREAM CAN -
then turn the power back on.)
11. Ice cream should churn for approximately 30-40 minutes. CAN will
STOP turning when ice cream is complete. Switch power to Off, unplug
cord and remove the MOTOR DRIVE. Motor will not turn back on until it
cools down - approximately 15-25 minutes. NOTE: Should ice cream
maker stop before churning is complete, check to see if ice cubes are
jammed against the rotating ICE CREAM CAN.
12. Once MOTOR DRIVE is removed, clear away ice and salt from the top
of the ICE CREAM CAN COVER. Carefully remove COVER and DASHER.
Recommend to use a rubber spatula to remove the ice cream from
the DASHER.
NOTE: Before using for the first time, wash all parts except MOTOR DRIVE
(see “HOW TO CLEAN YOUR ICE CREAM MAKER”).
1. Mix your favorite ice cream recipe thoroughly in a bowl PRIOR to putting
it in the DASHER. TIP: Chill (in the refrigerator) ice cream mixture and ICE
CREAM CAN prior to making ice cream.
2. While ice cream mixture and CAN are chilling, place cleaned wood
bucket on a flat surface counter top. Place DASHER and COVER nearby.
3. Once mixture and CAN are chilled, remove from refrigerator to start
the ice cream making process.
DASHER
MOTOR DRIVE
POWER SWITCH
COVER
ICE CREAM CAN
BUCKET SLOT
WOODEN
BUCKET
LATCHING
HANDLE
DRAIN HOLE
BEFORE USE. FILL BUCKET
2 /
3
FULL OF WATER. LET SOAK FOR
90
MINUTES.
THIS WILL ALLOW THE WOOD TO SWELL TO ENSURE THE BUCKET DOES
NOT LEAK.
FRRVWDBK 4 QT_11EM3.indd 5-6 8/31/11 9:07 AM