RiTTO TWINBUS Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 197

background image

Installation: Assembly, connection and start-up

55

In

st

al

la

tio

n

Program bell buttons

One-man start-up

Two-man start-up

If the time limit has been exceeded:

Repeat the procedure.

If the programming procedure failed:

The memory of the comfort indoor video station is full when 10 bell buttons have already been programmed. If
necessary, delete all settings and reprogram the pushbutton that is needed.

Activity

Result

Activate the programming status via the menu item
Program

bell buttons

Activity

Result

Activate the programming status via the menu item
Program bell buttons

✔

Short tone: Device is ready for operation.

/

No tone: Time limit exceeded.

/

Long tone: Programming procedure failed.

Program bell buttons

Programming status active

Programmed door calls: x

Back with <OK>

flashes

Within one minute, press the button
to be assigned on the door station

RiTTO

acoustic signal for confirmation at
indoor telephone and indoor video
station

RiTTO

Program bell buttons

Programming status active

Programmed door calls: x

Back with <OK>

flashes

RiTTO

announce button to be assigned via
speech connection

Within one minute, press the button
to be assigned on the door station

RiTTO

acoustic signal for confirmation at
indoor telephone and indoor video
station

RiTTO

«
...
53
54
55
56
57
...
»

Содержание TWINBUS






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TWINBUS

Бренд: EAW Страницы: 2

Бренд: EAW Страницы: 20

Бренд: Phase Technology Страницы: 11

Feeder/Deliming System EV9797-20

Бренд: Everpure Страницы: 2

Бренд: TCL Страницы: 48

Бренд: salmson Страницы: 195

AeGIS 8000 PLUS

Бренд: PACH & COMPANY Страницы: 30

Бренд: YeriSystems Страницы: 7

Бренд: Toa Страницы: 1

Бренд: Vitek Страницы: 28

Бренд: M-E Страницы: 40

EcoZone ConServer

Бренд: IrriGreen Страницы: 29

Бренд: Fusion Страницы: 4

Бренд: Monacor Страницы: 12

Бренд: GAS Страницы: 2

Бренд: Technics Страницы: 68

Villa Door Station

Бренд: Dahua Страницы: 37

Бренд: Contec Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды