Ritron RLR-465NX страница 1 Скачать руководство пользователя | Manualshive

Страница: 1 / 10

background image

Model: RLR-465NX

UHF, NXDN

™

Digital Liberty Repeater, 10 W, 6.25 kHz

ALIGNMENT AND DUPLEXER TUNING INSTRUCTIONS

FOR USE BY AUTHORIZED SERVICE/MAINTENANCE PERSONNEL ONLY

Ritron Pub:

RLR-465NX-ALIGN

01/21

© 2021 Ritron, Inc. All rights reserved.

Ritron, Inc. is a trademark of Ritron, Inc.
NXDN™ is a trademark of JVC Kenwood Corporation

Call 800-USA-1-USA

For the right Wireless Solutions for your communication needs.

P.O. Box 1998

·

Carmel, Indiana 46082-1998

· Ph:

317-846-1201

·

Fax: 317-846-497

Email: [email protected]

· www.ritron.com

Have questions?

Call 800-USA-1-USA

(800-872-1872) or visit our website at

www.ritron.com

1
2
3
...
»

Содержание RLR-465NX











Отзывы:

Нет отзывов

Похожие инструкции для RLR-465NX

Бренд: Lasko Страницы: 4

Бренд: NARVI Страницы: 48

Бренд: Mark Страницы: 128

Бренд: Eco Heat Страницы: 2

Бренд: Solbee Страницы: 4

Бренд: S-Access Страницы: 26

Repeater RP 6004

Бренд: DIS Страницы: 14

Бренд: Costway Страницы: 9

Бренд: Rapid Engineering Страницы: 64

ACX1M-CC SERIES

Бренд: Black Box Страницы: 40

Бренд: Creda Страницы: 12

Бренд: Goldair Страницы: 12

Watrod Electric Tubular Heaters

Бренд: Watlow Страницы: 2

Бренд: Sabiana Страницы: 41

Бренд: ARDES Страницы: 38

Бренд: Enerco Страницы: 24

Бренд: Optimus Страницы: 6

Бренд: Draper Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды