Ritron RF320 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 36

Ritron RF320 Series Скачать руководство пользователя страница 9

RF320-Series Ritron VHF/UHF Radios

•

Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999
Edition. Copyright Telecommunications Industry Association.

To control exposure to yourself and others and ensure compliance with the
occupational/controlled environment exposure limits, always adhere to the
following procedures.

2.2.2 Guidelines

•

User awareness instructions should accompany device when transferred to
other users.

•

Do not use this device if the operational requirements described herein are
not met.

2.2.3 Instructions

Transmit only when people in the vicinity are at least the recommended
minimum lateral distance away, as shown in TABLE 2-1, from a properly
installed antenna according to installation instructions.

TABLE 2-1 lists the recommended minimum lateral distance for
bystanders in an uncontrolled environment from transmitting
antennas (i.e., monopoles over a ground plane or dipoles) at
several different ranges of rated radio power for mobile radios
installed on a vehicle.

NOTE

TABLE 2-1. Rated Power and Recommended Lateral Distance

Antenna Model

Rated Power
of Mobile Two-
Way Radio

Recommended
Minimum Lateral
Distance from
Transmitting Antenna

For the DTX-145:
Ram1545 (vertical whip)

7 W or less

29 cm (11.4 in)

For the DTX-445:
Ram1545 (vertical whip)
Cushcraft PE-457-6 (6dB Yagi)

10 W or less
10 W or less

17 cm (6.7 in)
56 cm (22 in)

2.2.4 Antennas

Install vertical omnidirectional antennas above a suitable ground plane taking
into account the recommended minimum distance in TABLE 2-1. The antenna
installation should additionally be in accordance with:

The requirements of the antenna manufacturer/supplier.

Instructions in the Radio Installation Manual, including minimum
antenna cable lengths.

3

«
...
7
8
9
10
11
...
»

Содержание RF320 Series





































Отзывы:

Нет отзывов