Ritron Radio-To-Intercom Bridge RIB-600Analog Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 36

Ritron Radio-To-Intercom Bridge RIB-600Analog Скачать руководство пользователя страница 32

Section 4

Operation

30

4.9

Relay Operation

Radios are equipped with a relay that can be set for a relay switch closure when the RIB-600Analog receives a valid signal.
The relay can be used to

provide a “Priority”, “Override” or “Emergency” switch closure to the PA amplifier, enabling the

received signal to play over the PA system.

The Blue and Green wires on the

9-Conductor Interface Cable are used to connect

the relay switch.

With the Relay Option enabled:

If Record and Play is disabled

The relay switch will close as soon as a valid signal is received, and will remain
closed as long as the signal is present.

If Record and Play is enabled

The relay switch will close as soon as a valid signal is received and will remain
closed until the recorded message has finished playing.

If Delay Message Playback is programmed

The relay switch will close as soon as a valid signal is received, and will remain
closed for the delay time and until the recorded message has finished playing.

If Replay Message Playback is programmed

The relay switch will close as soon as a valid signal is received, will remain
closed for any Delay Message Playback time and until the recorded message
has been repeated in it’s entirety.

Radio Operation Timeline

The following timeline explains operation for RIB-600Analog radios. In this example the RIB-600Analog is programmed for:



Record and Play



Delay Message Playback of 10 seconds



Repeat Message Playback 3 times



Relay Operation Enabled



Pre-Announce Tone Enabled

Strobe Light Operation

The RIB-600Analog relay can be used to operate a strobe light in a number of configurations via the 9-Conductor Interface
Cable. The cable can provide:



A normally open relay switch that closes on a received signal. The relay switch can handle up to 3A when used to
connect power to a strobe light.



A normally closed relay switch that opens on a received signal.



A +10.5VDC supply that can be used to power an LED strobe light rated at 400mA or less.



A ground connection that can be used to provide a switch closure to ground.

Example:

The strobe light and the relay function can be used to provide a visual indication that the Radio-To-Intercom Bridge
is being used. If located reasonably close to the installation site of the receiver, the strobe could be located in the
security office area.

RIB-600Analog receives

a valid receive signal

Received message

is recorded

10 second

delay

Pre-Announce

Tone plays

Recorded Message

plays

Recorded Message

replays 3 times

Relay switch is closed

«
...
30
31
32
33
34
...
»

Содержание Radio-To-Intercom Bridge RIB-600Analog





































Отзывы:

Нет отзывов