manualshive.com logo in svg

Ritron DTX-165-0, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Ritron DTX-165-0 Скачать руководство пользователя страница 3

1 

INTRODUCTION

 

 

1.1 

GENERAL 

The RITRON High Power DTX Plus modules are programmable 2-way radios, which operate 
either in the VHF or UHF professional FM communications bands as well as a number of other 
bands in the 220 MHz, 350 MHz, and 900 MHz region.  Each of eight channels can be 
programmed to contain a unique set of operating frequencies.  The High Power DTX Plus module 
is made up of two PC boards, an RF board and a control/loader board.  These two boards are 
enclosed in a metal case with two connectors on one end; a 50 ohm BNC connector for 
connection to an antenna and a DB-15 sub-miniature connector for control input/output and a 
power input connector on the other end. 
 
In addition, the RF board/heat sink assembly is available as a stand-alone unit for system 
integrators.   

 

1.2 

MODEL IDENTIFICATION 

The part number system for the High Power DTX Plus module is as follows: 

 

The module has a part 

number in the form of  “DTX-A65-BCDEF” where: 

 

A is the major frequency band designator: 

 

 

1=VHF (136-174 MHz bands) 

 

 

2=216-222 MHz band 

 

 

3=340-400 MHz bands 

 

 

4=UHF (400-430 MHz and 450-470 MHz bands) 

 

 

9=896-901 MHz band 

 

B is the sub-band designator: 

 

 

G=136-162 for #1 above ,  340-360 MHz for #3 above, and 400-430 MHz for #4 above. 

 

 

A=420-440 

 

 

B=430-450 
O=148-174 for #1 above, 216-222 for #2 above, 360-380 for #3 above, 450-470 for #4 

above, and 896-901 for #9 above. 

 

 

M=380-400 for #3 above. 

 

 

C=470-490 

 

 

T=490-512 

 

 

Note that not all of the sub-bands listed above may be available, and that other sub-
bands may become available. 

 

C is the connector designator: 

 

 

B=BNC connector 

 

 

 

D designates the IF bandwidth: 

 

 

W=wide (25/30 kHz channel bandwidth) 

 

 

N=narrow (12.5/15 kHz channel bandwidth) 

 

 

S=very narrow (5/ 6.25/ 7.5 kHz channel bandwidth) 

 
 

E designates the maximum power level: 

 

 

30=30 watts 

 

 

 

F designates whether the control/loader board has a regulator and if so, at what current level: 

 

 

I=high current regulator; the unit operates from 10-15 volts at 30 watts max. 

 

Example:  A DTX-265-OBN30I would be a VHF module for operation between 216 and 222 MHz 
with a BNC RF connector, narrow (12.5 kHz channel bandwidth) IF bandwidth, 30 watts 
maximum output power, and an internal regulator to allow operation from 10 to 15 volts. 
 

Содержание DTX-165-0































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды