Rise RXD250 Скачать руководство пользователя страница 6

Страница: 6 / 12

RADIO SYSTEM

Your transmitter needs to have a switch for channel 5. The setup below is

typical for most transmitters. The receiver must have one port for each
channel. S-bus, X-bus, and satellite receivers cannot be used with the 8 pin
receiver cable.

CHANNEL ASSIGNMENTS

MODEL TYPE: Airplane

Channel

Aileron

Elevator

Throttle

Rudder

Gear

Direction

normal
normal
normal
normal
normal

Dual Rates

80/100
80/100

80/100

Expo

-30/0
-30/0

-30/0

End Points

100/100
100/100
100/100
100/100
100/100

SWITCH ASSIGNMENTS - Ch 5

Gear
Gear
Gear

-100%

+100%

Stability

Rattitude

Rate

Black

Red

Throttle

White

Blue

Yellow

Green

Yellow

Black

Roll

Pitch

Yaw

Ch5

Ch6

Mount the receiver just in front of
the flight controller. Install the

antenna mounts as illustrated or
run the antenna down through the
frame.

Receiver location

Mount the receiver

with double-sided tape.

Antenna

Connect the receiver to
the CC3D flight controller.

Содержание RXD250













Результаты поиска

Содержание RXD250

Отзывы:

Бренды по названию

Популярные бренды

Rise RXD250, Инструкция по эксплуатации

Результаты поиска

Содержание RXD250

Отзывы:

Бренды по названию

Популярные бренды