4
1.
Set the mobile device holder by having the side of open and close
red switch on the right side of the scanner as presented on the
above image.
2.
CAUTION: Please do not pull or press on any of the 4 extensions
or legs of the holder, for it can unbalance and disrupt the normal
functionality of the holder’s 4 extensions.
3.
Place the mobile device holder lightly on the top of the base, so
the 4 elevated studs fit into the 4 holes of the holder.
4.
Press the holder to the scanner firmly and draw back very
carefully until you hear a low clicking sound.
5.
To separate the holder from the scanner: Press on the holder
towards the scanner firmly, then push it forward carefully.
6.
IMPORTANT: We do not recommend the repetitive action of
detaching and reattaching the holder.
7.
Place the smartphone onto holder (Recommendation: use
mobile device less than 14.5 cm in length), plug the micro usb to
the mobile device, then close in the extensions.
8.
Push in the tiny rectangular switch at the bottom of the handle,
then switch the scanner to Operation mode, now it can scan
directly to the mobile’s APP. The user
may choose to connect
through Bluetooth as well (Please review the different ways of
connection at page 2 and 3, for a more detail explanation).
There are two operating modes on the scanner
1.Data Transmission Mode
(Default)
Demo
%M%A%F
It is a necessary to scan “
Clean Memory Data
” when
switching between these two modes.
Within Bluetooth radio range
Beyond Bluetooth radio range
Data
read
Transmit data to
smartphone/tablet directly
Save data in scanner’s memory,
scanner will transmit data to
smartphone/tablet automatically
after getting back to Bluetooth
radio range.
Enter Data Storage mode
LED
Green/ Orange LED flashes,
followed by 3 beeps.
2. Data Storage mode (Batch Mode)
Demo
%M%A%N
It is a necessary to scan “
Clean Memory Data
” when
switching between these two modes.
Data
read
Save data directly to scanner’s memory. It will transmit data to
smartphone/tablet after you scan the Transmit memory data
code. To delete data, please scan the
Clean Memory Data
code.
Enter Data Transmission mode
LED
Green/ Orange LED flashes followed by 3 beeps.
Always
Clean Memory Data
before switching to Data Transmission
Mode.
Otherwise Red/ Orange LED will flash with one long beep sounds
and will not switch modes.
A.
Data Transmission mode
(Default)
1.
When you are out of BT signal range,
the data you scan will be saved to
memory. Once you are back within
range, the data will be sent to
smartphone/tablet automatically.
B.
Data Storage mode(Batch mode)
1.
Data Storage mode (Batch mode):
When you scan the barcodes, the data
will be saved directly to scanner’s
memory. After you scan the
“Transmit memory data” code
(above right), the data will be sent to
smartphone/tablet.
2.
Before you can continue to scan or
switch modes, you must first delete
the data stored in the memory. To do
this, scan the “
Clean Memory Data
”
code.
Demo
%R%E%C
Transmit memory data
Green/Orange LED flashes
followed by 3 beeps
The barcode data which is stored
in the memory will be sent to
smartphone/tablet directly.
(under Batch mode, within
Bluetooth service range)
Demo
%E%R%A
*Clean Memory Data
Green/Orange LED flashes
followed by 3 beeps.
The barcode data which is stored
in the memory will be deleted. You
can then switch modes.
Holder’s back with 4 holes to
lock up with the scanner
4 Elevated Studs to fit into the
4 holes of the Holder’s back.
Holder’s front side: Make sure the red switch is on the right
side (exactly as this picture shows), when fitting the 4 holes
of the holder to the 4 studs of the scanner
1. Holder’s front side: In order to
shrink or spread the 4
extensions, shift and Hold the
red switch to Open while you
rotate the wheel either way,
2. Do not pull or push the 4
extensions, nor extend the
wheel across the limit, for it
can disrupt the balance and
functionality of the holder.
3. Use mobile device less than
14.5 cm in length.