Trigger Mode
Trigger always
(Trigger available at any time)
Trigger standard
(Trigger available, after data sent to the device)
(Default)
Transmission Speed
Transmission speed is dependent on your device. In order not to lose data,
please choose the correct speed. Middle-speed is the Default.
High-speed
Ultra Slow-speed
transmission 1 transmission
Middle-speed
Ultra
Slow-speed
transmission 2 transmission
Slow-speed
Ultra
Slow-speed
transmission
(Default)
3 transmission
Power-saving Mode
Power-saving mode OFF
Power-saving mode ON (Default):
Enter power-saving mode after 1-minute inactivity.
This function converses battery power. When you
press "SCAN/Power ON" button, it will wake up and
begin to scan.
*
When charging, the scanner will not enter power-saving mode automatically.
RTC (Real-time clock), please set the punctuation mark
at the same time
You must scan the below configuration barcode to set the date & time stamp on
the scanner.
Date information:
ENABLE
Date
information:
DISABLE (default)
Time information:
ENABLE
Time
information:
DISABLE (default)
The format of Date setting
Date format 1: mm/dd/20yy (default)
For example: 01/23/2011
Date format 2: dd/mm/20yy
For example: 23/01/2011
Date format 3: 20yy/mm/dd
For example: 2011/01/23
The punctuation marks for the intervals among barcode
data, date, time
, comma (default) – FOR Android/iOS use
For example:
ABCD,01/23/2011,12:34:56
Tab – FOR iOS use
For example:
ABCD 01/23/2011 12:34:56
; semicolon – FOR Android/iOS use
For example:
ABCD;01/23/2011;12:34:56
Date and Time setting
SET DATE
Scan the SET DATE barcode, then, scan the six
numeric digits in the format mm/dd/yy, from the
numberic barcode.
For example: “01/23/2011”, please input 012311
SET TIME
Scan the SET TIME barcode, then, scan the six
numeric digits in the format hh:mm:ss from the
numberic barcode. Time format: 24hr clock
For example: “PM 3:25:30”, please input “152530”
How to append a “prefix” or a “suffix” to the barcode data
prefix
suffix
1.
scan above configuration code for Prefix or Suffix
2.
enter the required values (right, numeric barcode) for Prefix or Suffix using
the hex values for the desired HEX values from Prefix & Suffix TABLE
(below page)”
3.
then, end by scanning Code X (below, right)
*
The max. of special characters is 5.
*
When you append 1~4 required values for Prefix or Suffix, it must end with
Code X.
*
It doesn’t need Code X, if you append 5 values to barcode data.
How to delete Prefix or Suffix
1.
scan above configuration code for Prefix or Suffix
2.
enter the “0” “0” (above, right)
3.
then end by scanning Code X (below, right)
Keyboard
Country
Scan the appropriate country code below to program
the keyboard for your country or language. As a
general rule, the following characters are not
supported by the scanner for countries other than
the United States: @ | $ # { } [ ] = / ‘ \ < > ~
Follow the steps mentioned below to program.
1.
Keyboard Country setting code.
2.
“Select Country Code”
Read numeric barcode (according to country code).
Country/
Language
No.
Country/
Language
No.
Country/
Language
No.
U.S. 10
Netherlands
26
Switzerland
French
45
Latin
America
11
Hungary 27
Switzerland
German
46
Brazil 12
Italian 28
Sweden 47
Belgium
20
Icelandic
29
Turkey F
48
Bulgarian
Latin
21
Norway 30
Turkey
Q 49
Denmark 22
Poland 41
Japan
71
Finland 23
Portugal 42
Korea
72
France 24
Russia 43
Thai
73
Germany 25
Spain 44
Vietnam 74
Numeric barcode for settings
0
6
C
1
7
D
2
8
E
3
9
F
4
A
5
B
X
3