RioOutdoors 6S-DH Скачать руководство пользователя

Страница: 18 / 31

18 |

P a g e

1.10

HEADERS PREPARATION

We recommend a maximum header length of 12 feet for 2x6 headers and 16 feet for 2x8 headers. The recommended rafter

lengths are 12 feet for 2x6 rafters and 16 feet for 2x8 rafters. We further recommend that you allow for 18” of overhang

beyond the posts on each side for the headers and 18” overhang beyond the headers on each side for the rafters.

1.10.1

Header and Rafter Tail Designs Cutting

Visit www.

https://riooutdoors.com/rafter-tail-designs

to see our collection of Rafter Tail designs. Based on your cosmetic

preference and woodworking skill level, select a rafter tail design shape that you plan to cut yourself or you plan to outsource the

design cutting. You may have your own design that you wish to apply to the rafter tails. The possibilities for rafter tail designs are

endless, and a minor change in detail can add a dramatic flair to your pergola design. Be creative.

1.10.2

Rafter Tie Brackets Installation

For a dual header pergola system, rafter ties are required to be installed on both top headers on each side of the pergola. The

rafter ties are to be installed in an offset pattern between the two headers, as shown in the image, below. This offset pattern

helps prevent warping of both headers and further helps to stiffen the pergola structure and prevents swaying motion.

OUTER HEADER

INNER HEADER

NOTE THE OFFSET

MOUNTING PATTERN FOR

THE RAFTER TIE BRACKETS

Содержание 6S-DH
































Результаты поиска

Содержание 6S-DH

Отзывы:

Похожие инструкции для 6S-DH

Бренды по названию

Популярные бренды

RioOutdoors 6S-DH, Руководство по установке

Результаты поиска

Содержание 6S-DH

Отзывы:

Похожие инструкции для 6S-DH

Бренды по названию

Популярные бренды