STITCH LINE
6. Rotate all eight Leg Poles upright and insert pin on each
web loop at the side locations as shown. (Fig. 7 & 7A)
Fig. 6
Fig. 7
7A
Pin
9. Insert plastic stakes through web straps located on
both sides of tent, then drive in to secure. (Fig. 10)
NOTE:
It may be necessary to remove metal stakes
through web straps at side of tent and screen room,
pull tent taut, and drive in stakes to secure.
Fig. 10
7. Locate the plastic hooks at sides and
corners of tent, then snap onto Leg Poles to
attach. (Fig. 8)
Fig. 8
8. To stretch tent to fi nished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise
(Fig.9);
• Pull up on top Leg Pole section until
tent is taut;
•
Twist the lower Leg Pole clockwise
until the button locks into the center or
lowest
hole;
•
Repeat on remaining Leg Poles.
Fig. 9
Button
Center Hole
Lower Hole
Lower
Leg Pole
Section
Upper
Leg Pole
Section
ELITE WEATHERMASTER
®
TENT
MODEL 2000005748
Curved Ridge Poles with Red Markings in center sleeves
4. Assemble eight, steel, shock-corded, Leg Poles.
Push down on steel button on tapered end and
insert into end with four holes.
NOTE: Make sure steel button locks into third
hole on pole as shown. (Fig.4)
5. Insert curved end of Leg Poles
(with red marking) into the
ends of the Ridge Pole (with
red marking). Insert curved
end of remaining short Leg
Poles into the ends of the
remaining Ridge Poles.
(Fig. 5 & 6)
Fig. 1
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the door facing
the desired direction. Unzip doors. (Fig. 1)
Door
Fig. 2
2. Pull four corners of tent taut, then secure by driving
stakes through web loops at an angle for better
anchoring. (Fig. 2)
Ridge Pole
with Red
Marking
Fig. 3
Sleeve
with Red
Trim
3. Assemble four, steel, shock-corded, curved
Ridge Poles. Insert Ridge Poles (with red
marking) into center sleeves on top of tent with
the red trim (Fig. 3). Insert the remaining curved
Ridge Poles into the other two sleeves on top of
tent.
Ridge Pole with
Red Marking
Fig. 5
Sleeve
with Red
Trim
Curved End of
Long Leg Pole
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips); then insert
through zippered vertical pole sleeve on hinged side of door. (Fig. 11)
2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to
form a slight bow, then insert other tip of pole into top hinge. Zip up verti-
cal pole sleeve. (Fig. 12 & 13)
3. Assemble Door Pole (longer black pole with plastic cap tips); then insert
into zippered pole sleeve at top of door. (Fig. 14)
4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow,
then insert other tip of pole into the bottom hinge. (Fig. 15)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 11
Fig. 12
Fig. 13
Vertical Pole
Sleeve
Door Hinge
Fig. 14
Fig. 15
Fig. 16
Pole
Sleeve
Top
Door
Hinge
Pole
Sleeve
Top
Door
Hinge
(continued on other side)
Pole Descriptions
Pole
Pole
Description
Qty. Repair Kit
Replacement Kit
Long Leg Pole, steel
(w/ red marking)
4
N/A
5010000754
Short Leg Pole, steel
4
N/A
5010000755
Curved Ridge Pole, steel
(w/ red marking)
2
N/A
5010000756
Curved Ridge Pole, steel
2
N/A
5010000757
Awning Pole, black,
fiberglass, metal tips
2
5010000543
5010000545
Door Pole, long, thin, black,
fiberglass, rubber tips
1
5010000543
5010000545
Vert. Door Pole, short, black,
fiberglass, rubber tips
1
5010000543
5010000545
Before you begin
Read all instructions before set up.
Select a level site clear of rocks, branches, and other hard or sharp
•
objects, to install your tent.
WARNING: Keep clear of overhead power lines.
Do not set up your tent under trees because of potential lightning strikes or
•
falling tree limbs in inclement weather.
Secure with
•
all
stakes and guylines provided to prevent property damage
or personal injury.
For best results in windy conditions, position narrow end of tent into the wind.
•
Enlist the help of at least one other person to assist you when it is time to
•
assemble the tent.
Self-Rolling Window Spring Descriptions
Color Code Description
Qty.
Replacement Part No.
Red
1
5010000624
Yellow
2
5010000626
Green
1
5010000627
Orange
2
5010000628
CAUTION:
“Springs” may have sharp edges. Handle with care to avoid injury.
Keep out of reach of children.
Button in third hole
Fig. 4
