background image

RINNAI UK WARRANTY

As the purchaser of this high quality Rinnai Water Heater you are provided with the following         
conditional warranty

Definition of Standard Use. 

 
The warranty period allocated under Standard Use is based on Domestic and Light Commercial hot 
water usage.  Rinnai Standard Use warranty periods apply only where Rinnai water heaters are     
installed in domestic and light commercial situations at operating temperatures below 65 

°

C and do not 

include installations incorporating storage cylinders or building flow and return systems. 
 
The warranty shall apply to any Rinnai water heater from the Infinity range used in this way. 

 

Definition of Commercial Use. 

 
The warranty period allocated under Commercial Use are for Infinity water heaters installed at  
premises such as commercial and industrial buildings, cafes, caravan parks, and sporting complexes.  
Commercial Use warranty applies to: 
 
Water heaters supplying a central shower block.
Water heaters supplying kitchens used for the bulk preparation of food. 
Water heaters set to 65 

°

C or higher. 

Water heaters used in commercial or industrial processes. 
Any application that uses Rinnai water heaters in conjunction with storage tanks. 
Any application that uses Rinnai water heaters in conjunction with a flow / return system. 
Water heaters installed as components of centralised bulk hot water systems. 
 
Rinnai Infinity units used in Commercial Situations are only subject to a 1 year warranty across     
the board. Commercial situations should be supplied 

from 

the Rinnai Commercial range. 

No Rinnai warranty will cover faults arising from improper installation or gas supply, water          

    

contaminants beyond defined limits, environmental factors, plumbing fittings, or other outside    

     

influences of which Rinnai is not responsible.  Service calls for these issues will be chargeable. 

Heat Exchanger 

All Other Parts 

Parts Labour Parts Labour 

Standard Use 

3 Ye

1 Y

ars 

1 Year 

3 Years 

1 Year 

 Infinity 20e
 Infinity 16e

 Infinity 20e
 Infinity 16e

Commercial Use 

ear* 

1 Year 

1 Year 

1 Year 

Description

pH

Total Dissolved 

Solids (TDS) 

Total Hardness  Chlorides 

Magnesium 

Calcium 

Sodium 

Iron 

Maximum Recommended 

Levels 

6.5 - 9.0

600 mg/litre 

200 mg/litre 

300 mg/litre  10 mg/litre 

20 mg/litre  150 mg/litre  1 mg/litre 

2

Содержание Infinity 16e









































Отзывы: