A
S
S
E
M
B
L Y
–
G
E
N
E
R
A
L
TEST FOR LEAKS WITH A
SOAP SOLUTION, NEVER WITH AN
OPEN FLAME (Refer pages 3 and 4).
CONNECTING TO, AND DISCONNECTING
FROM GAS SOURCE
CONNECTING TO GAS SOURCE
1.
Hang filled gas cylinder on the cylinder hook.
2.
Attach cylinder connection
device of regulator and hose
assembly to cylinder
valve outlet.
Tighten firmly.
3.
Open the gas
cylinder valve fully
to allow gas to flow.
4.
Leak test all accessible
connections thoroughly
using a soapy water
solution prior to lighting the barbecue.
Refer to Safety information, page 3.
5.
If a leak is found, turn gas cylinder valve off and do
not use barbecue until repairs or replacement can
be made.
DISCONNECTING FROM GAS SOURCE
1.
Turn the burner control
‘OFF’
.
2.
Turn the gas cylinder valve off fully.
3.
Detach the regulator assembly from gas cylinder
valve.
IMPORTANT: Before connecting and disconnecting
barbecue to gas source, ensure burner controls are
in ‘OFF’ position.
NOTE: The ‘OFF’ position on the control panel is
identified by either a small black dot / a short vertical
black line / or the word ‘OFF’.
When the marking, or the word ‘OFF’ printed
on the control knob, aligns with the printed marking
on the control panel, then the burner is in the fully
off position.
CAUTION: When the appliance is not in use, the gas
must be turned off at the gas cylinder
.
Familiarise yourself with the general information and
safety guidelines located at the front of this booklet.
Check to see that gas cylinder is filled and that end of
each burner tube is properly located over each valve
orifice. Set burner controls to
‘OFF’
position.
ENSURING BURNER CONTROLS ARE OFF
• DISCONNECT AND REMOVE GAS
CYLINDER WHEN MANOEUVRING THE
BARBECUE OVER UNEVEN SURFACES
OR CARRYING UP AND DOWN STAIRS
• IF THIS INFORMATION IS NOT
FOLLOWED EXACTLY, A FIRE
CAUSING DEATH OR SERIOUS INJURY
MAY OCCUR!
• DO NOT STORE A SPARE GAS
CYLINDER UNDER OR NEAR THIS
APPLIANCE
• THIS BARBECUE IS ONLY TO BE
USED OUTDOORS.
Direction for
tightening
Install Ignitor Battery
Remove Ignitor Cap from Control Panel.
Place supplied AA battery into the Ignitor
Slot with positive pole facing you.
Position the Cap and Spring over the
AA battery and tighten onto Control Panel.
Ignitor Cap
Ignitor Slot
AA Battery
Spring
+
-
21
21
Содержание GT3-V
