Rinnai ES17 Скачать руководство пользователя

Страница: 8 / 44

Rinnai Corporation ES17 / ES22 Manual

Operating the Heater Manually

Turning the heater ON

When you press and release the ON/OFF button, the

Temperature Level lamps will illuminate, the

combustion fan will begin to run, and the spark will

ignite the main burner.
This heater has an automatic ignition system. When

the main burner has lit, the combustion lamp will glow

red, and the spark will stop.
If ignition does not occur after 15 seconds, the

appliance will automatically turn off and the

Temperature Level lamps will flash indicating a fault

code. This may occur when using the appliance for

the first time or if it has not been used for a while. Try

operating the appliance again.
There may be a smell of burning dust or oil the first

time the heater is lit or when the heater has been out

of operation for a long time.
The appliance may make noises after ignition or when

it is turned off. This is normal and is due to the

thermal expansion or contraction of its components.

Adjusting the Temperature

The temperature setting and the room temperature are

indicated by the L.E.D. display on the control panel.

When the appliance is turned on the temperature

setting will be displayed for 10 seconds. The display

will then show the room temperature. The default

temperature setting is 72° F.
To change the temperature setting press one of the

temperature control buttons once. The “Set Temp”

should light up and the display will show the current

temperature setting. Continue to press the control

buttons until the desired temperature setting is

reached. After 10 seconds the display will return to

showing the room temperature.
The thermostat automatically modulates the burner

and the fan to maintain the temperature setting.
The temperature settings available are:

•

LO - burner is on minimum combustion

•

60° F - 80° F in two degree increments

•

HI - burner is on maximum combustion

Turning the heater OFF

Press the ON/OFF button. Do not

turn off by unplugging at the power

outlet.
The fan will continue to run for a short time to prevent

the internal components from overheating.

ON/OFF

Economy Mode

Pressing the Economy button will cause

the appliance to go into Economy Mode

and the green lamp will glow. This results

in the temperature setting being reduced by

2° F, 30 minutes after the room

temperature has reached the temperature

setting. After another 30 minutes the

temperature setting is reduced another 2°

F. This could result in the temperature

setting being reduced by a maximum of 4° F. The

intent of this mode is to save energy.
When the heater is running at the LO setting, the

Economy Mode does not function.

Economy

ON/OFF

Filter

RoomTemp

Set Temp

Temp

Control

Содержание ES17













































Результаты поиска

Содержание ES17

Отзывы:

Похожие инструкции для ES17

Бренды по названию

Популярные бренды

Rinnai ES17, Руководство пользователя

Результаты поиска

Содержание ES17

Отзывы:

Похожие инструкции для ES17

Бренды по названию

Популярные бренды