Rigol DS4000E Series Скачать руководство пользователя страница 192

Страница: 192 / 278

RIGOL

Chapter 2 Command System

2-180

DS4000E Programming Guide

:SYSTem Commands

Command List:











:SYSTem:ERRor[:NEXT]?













:SYSTem:OPTion:INSTall



:SYSTem:OPTion:UNINSTall





















:SYSTem:AOUTput

Syntax

:SYSTem:AOUTput <aoutput>

:SYSTem:AOUTput?

Description

Sets or queries the type of the signal output from the [Trig Out/Calibration] connector on the rear

panel.

Parameter

Name

Type

Range

Default

<aoutput> Discrete

{TOUT|QEDGe|GND|PFAil}

TOUT

Remarks



TOUT: indicates that each time the oscilloscope triggers, a signal that can reflect the current capture

rate of the oscilloscope will be output from the [Trig Out/Calibration] connector on the rear panel.



QEDGe: indicates that a fast edge signal whose rise time is 500 ps will be output from the [Trig

Out/Calibration] connector on the rear panel. The signal can be used for the self-calibration of the

oscilloscope.



GND: indicates that a ground level will be output from the [Trig Out/Calibration] connector on the rear

panel.



PFAil: indicates that when a failed waveform is detected by the oscilloscope, a pulse will be output

from the [Trig Out/Calibration] connector on the rear panel.

Return Format

The query returns TOUT, QEDG, GND, or PFA.

Содержание DS4000E Series























































































































































































































































































Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol DS4000E Series, Руководство по программированию

Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды