Riello Vokera Linea ONE Скачать руководство пользователя страница 10

8

SECTION 3 - GENERAL REQUIREMENTS (UK)

This appliance must be installed by a competent person in accord-

ance with the Gas Safety (Installation & Use) Regulations.

3.1  RELATED DOCUMENTS

The installation of this boiler must be in accordance with the relevant 

requirements of the Gas Safety (Installation & Use) Regulations, 

the local building regulations, the current I.E.E. wiring regulations, 

the bylaws of the local water undertaking, the Building Standards 

(Scotland) Regulation and Building Standards (Northern Ireland) 

Regulations.

It should be in accordance also with any relevant requirements of 

the local authority and the relevant recommendations of the following 

British Standard Codes of Practice.

3.2 LOCATION OF APPLIANCE

The appliance may be installed in any room or internal space, al-

though particular attention is drawn to the requirements of the current 

I.E.E. wiring regulations, and in Scotland, the electrical provisions 

of the Building Regulations, with respect to the installation of the 

appliance in a room or internal space containing a bath or shower.

When an appliance is installed in a room or internal space contain-

ing a bath or shower, the appliance or any control pertaining to it 

must not be within reach of a person using the bath or shower. The 

location chosen for the appliance must permit the provision of a safe 

and satisfactory flue and termination. The location must also permit 

an adequate air supply for combustion purposes and an adequate 

space for servicing and air circulation around the appliance. Where 

the installation of the appliance will be in an unusual location special 

procedures may be necessary, BS 6798 gives detailed guidance on 

this aspect. A compartment used to enclose the appliance must be 

designed and constructed specifically for this purpose. An existing 

compartment/cupboard may be utilised provided that it is modified to 

suit. Details of essential features of compartment/cupboard design 

including airing cupboard installations are given in BS 6798. This 

appliance is not suitable for external installation.

3.3 GAS SUPPLY

The gas meter – as supplied by the gas supplier – must be checked 

to ensure that it is of adequate size to deal with the maximum rated 

input of all the appliances that it serves. Installation pipes must be 

fitted in accordance with BS 6891.

Pipe work from the meter to the appliance must be of adequate 

size. Pipes of a smaller size than the appliance gas inlet connection 

must not be used. The installation must be tested for tightness in 

accordance with BS6891.

If the gas supply serves more than one appliance, it must be ensured 

that an adequate supply is maintained to each appliance when they 

are in use at the same time.

3.4 FLUE SYSTEM

The terminal should be located where the dispersal of combustion 

products is not impeded and with due regard for the damage and 

discoloration that may occur to building products located nearby.  The 

terminal must not be located in a place where it is likely to cause a 

nuisance (see fig. 4). In cold and/or humid weather, water vapour 

will condense on leaving the terminal; the effect of such pluming 

must be considered.

If installed less than 2m above a pavement or platform to which 

people have access (including balconies or flat roofs) the terminal 

must be protected by a guard of durable material.  

The guard must be fitted centrally over the terminal. Refer to BS 

 

BS 5440 

PART 1 

FLUES 

 

BS 5440 

PART 2 

FLUES & VENTILATION 

  BS 5449 

PART 1 

FORCED CIRCULATION HOT WATER SYSTEMS 

  BS 5546 

 

INSTALLATION OF GAS HOT WATER SUPPLIES FOR  DOMESTIC PURPOSES

  BS 6798 

 

INSTALLATION OF BOILERS OF RATED INPUT NOT  EXCEEDING 60kW

  BS 6891 

 

LOW PRESSURE INSTALLATION PIPES 

 

BS 7074 

PART 1 

APPLICATION, SELECTION, AND INSTALLTION OF EXPANSION VESSELS  

   

 

AND ANCILLARY EQUIPMENT FOR SEALED WATER SYSTEMS 

5440 Part 1, when the terminal is 0.5 metres (or less) below plastic 

guttering or 1 metre (or less) below painted eaves.

3.5 AIR SUPPLY

The following notes are intended for general guidance only. This 

appliance is a room-sealed, fan-flued boiler, consequently it does 

not require a permanent air vent for combustion air supply. When 

installed in a cupboard or compartment, ventilation for cooling pur-

poses is also not required.

3.6 WATER CIRCULATION

Detailed recommendations are given in BS 5449 Part 1 and BS 

6798. The following notes are for general guidance only.

3.6.1 PIPEWORK

It is recommended that copper tubing to BS 2871 Part 1 is used 

in conjunction with soldered capillary joints. Where possible pipes 

should have a gradient to ensure air is carried naturally to air release 

points and that water flows naturally to drain cocks. Except where 

providing useful heat, pipes should be insulated to avoid heat loss 

and in particular to avoid the possibility of freezing. Particular atten-

tion should be paid to pipes passing through ventilated areas such 

as under floors, loft space and void areas.

3.6.2 AUTOMATIC BY-PASS

The appliance has a built-in automatic by-pass, consequently there 

is no requirement for an external by-pass, however the design of the 

system should be such that it prevents boiler ‘cycling’.

3.6.3 DRAIN COCKS

These must be located in accessible positions to facilitate draining 

of the appliance and all water pipes connected to the appliance. The 

drain cocks must be manufactured in accordance with BS 2879.

3.6.4 AIR RELEASE POINTS

These must be positioned at the highest points in the system where 

air is likely to be trapped. They should be used to expel trapped air 

and allow complete filling of the system.

3.6.5 EXPANSION VESSEL

The appliance has an integral expansion vessel to accommodate 

the increased volume of water when the system is heated. It can 

accept up to 8 litres of expansion from within the system, gener-

ally this is sufficient, however if the system has an unusually high 

water content, it may be necessary to provide additional expansion 

capacity (see 6.18).

3.6.6 FILLING POINT

A  method  for  initial  filling  of  the  system  and  replacing  water  lost 

during  servicing  etc.  directly  from  the  mains  supply,  is  provided. 

This method of filling complies with the current Water Supply (Water 

Fittings) Regulations 1999 and Water Bylaws 2000 (Scotland). If an 

alternative location is preferred, it should be connected as detailed.

3.6.7 LOW PRESSURE SEALED SYSTEM

An alternative method of filling the system would be from an inde-

pendent make-up vessel or tank mounted in a position at least 1 

metre above the highest point in the system and at least 5 metres 

above the boiler (see fig. 5).

The cold feed from the make-up vessel or tank must be fitted with 

an approved non-return valve and stopcock for isolation purposes. 

The feed pipe should be connected to the return pipe as close to 

the boiler as possible.

Содержание Vokera Linea ONE









































Отзывы: