2903397
2
GB
Contents
8.6.2 2nd stage adjustment....................................................................................................................................................21
8.7
Electrode setting............................................................................................................................................................21
8.8
Electronic start delaying device.....................................................................................................................................22
8.9
Burner start-up cycle .....................................................................................................................................................22
9
Maintenance ..............................................................................................................................................................................23
9.1
Notes on safety for the maintenance.............................................................................................................................23
9.2
Maintenance programme ..............................................................................................................................................23
9.2.1 Maintenance frequency .................................................................................................................................................239.2.2 Checking and cleaning ..................................................................................................................................................23
9.3
Maintenance position ...................................................................................................................................................24
10 Faults / Solutions ......................................................................................................................................................................25
