Riello 20118244, Руководство по установке и обслуживанию

Страница: 34 / 60

34
INSTALLATION
Menu
Par.
No.
Description Range
Default
setting
INSIEME
EVOe 25 K LN
Default
setting
INSIEME
EVOe 32 K LN
UM Access
Zone 2 Heating Settings
3000 3200
Use of Zone 2 control accessory
0 = NO
1 = Yes
If Zone 2 control accessory is used, AT and OT inputs
are not enabled. AT input is used only to enable the
night reduction on all the active zones (Par. 2001= 2
and 3)
0…1 0 0 I
3000 3201
Zone 2 mode
0 = direct
1 = mixed
0…1 1 1 I
2000 2203
Zone 2 heating setpoint in 0 and 3 heating modes
The thermal unit adjustment determines the boiler
setpoint in heating mode, using the highest value
among the requests of all the active zones (Par. 1101,
1201, 1301)
If Zone 2 is configured as mixed, the value set in
parameter 1113 will be used as setpoint.
BT: (Par. 2221,
45)
AT: (Par.
2221,Par.
2024)
70 (AT)
45 (BT)
70 (AT)
45 (BT)
°C U
2000 2219
Zone 2 maximum heating setpoint at the minimum
external temperature
The range of this parameter is limited by the values
of the Minimum (Par. 2023) and Maximum (Par. 2024)
setpoints.
BT: (Par. 2221,
45)
AT: (Par.
2221,Par.
2024)
82 (AT)
45 (BT)
82 (AT)
45 (BT)
°C I
2000 2221
Zone 2 minimum heating setpoint at basic external
temperature (Par. 2222)
It sets the minimum heating setpoint when the
external temperature is equal to the value set in
parameter 2222 (basic external temperature).
BT: (20, Par.
2219)
AT: (Par.
2023,Par.
2219)
30 (AT)
20 (BT)
30 (AT)
20 (BT)
°C I
2000 2220
Zone 2 minimum external temperature
It defines the minimum external temperature to
which the maximum heating setpoint Par. 2219 must
be associated.
-20…5 -20 -20 °C I
2000 2222
Zone 2 basic external temperature
It sets the external temperature at which the boiler
setpoint must be reduced, according to the value de-
fined in parameter 2221.
5...30 20 20 °C I
2000 2225
Zone 2 summer/winter switching
It blocks the heating request when the external tem-
perature is greater than this setpoint.
0...35 20 20 °C I
2000 2230 Parallel shift of direct Zone/Zone 1 climatic curve -10…10 0 0 °C U
2000 2231 Zone 2 mild climate temperature compensation 0...20 0 0 °C I
2000 2232
Zone 2 ambient temperature nominal value
When an OpenTherm (OT) ambient thermostat is con-
nected to the zone control accessory, this parameter
is not used.
5...35 20 20 °C I
2000 2234 Compensation factor of Zone 2 external temperature 0...100 50 50 % I
2000
2235 Zone 2 mixing valve closing time 0...240 140 140 sec I
2000 2236 Zone 2 mixing valve PID P 0...99 5 5 I
2000 2237 Zone 2 mixing valve PID I 0...99 10 10 I
2000 2238 Zone 2 valve operating time 0...255 2 2 I
2000 2239
Supply Extra
Only for MIX Zone
0...20 5 5 °C I
2000 2240 Zone 2 circulator post-circulating time 0...60 30 30 sec I
2000 2241 Zone 2 delivery overtemperature protection 0...100 55 55 °C I
2000 2242 Zone 2 overtemperature control time 0…240 0 0 min I
2000 2243 Zone 2 overtemperature stand-by time 0…240 2 2 min I
2000 2244 Zone 2 system reset time 0…240 2 2 min I
Zone 3 Heating Settings
3000 3300
Use of Zone 3 control accessory
0 = NO
1 = Yes
If Zone 3 control accessory is used, AT and OT inputs
are not enabled. AT input is used only to enable the
night reduction on all the active zones (Par. 2001 = 2
and 3).
0…1 0 0 I
3000 3301
Zone 3 mode
0 = direct
1 = mixed
0…1 1 1 I