background image

What is covered
RIDGID

®

tools are warranted to be free of defects in workmanship and material.

How long coverage lasts
This warranty lasts for the lifetime of the RIDGID

®

tool. Warranty coverage ends when the prod-

uct becomes unusable for reasons other than defects in workmanship or material.

How you can get service
To obtain the benefit of this warranty, deliver via prepaid transportation the complete product
to RIDGE TOOL COMPANY, Elyria, Ohio, or any authorized RIDGID

®

INDEPENDENT SERVICE

CENTER. Pipe wrenches and other hand tools should be returned to the place of purchase.

What we will do to correct problems
Warranted products will be repaired or replaced, at RIDGE TOOL’S option, and returned at no
charge; or, if after three attempts to repair or replace during the warranty period the product
is still defective, you can elect to receive a full refund of your purchase price.

What is not covered
Failures due to misuse, abuse or normal wear and tear are not covered by this warranty.  RIDGE
TOOL shall not be responsible for any incidental or consequential damages.

How local law relates to the warranty
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. This warranty gives you specific
rights, and you may also have other rights, which vary, from state to state, province to
province, or country to country.

No other express warranty applies
This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID

®

products. No

employee, agent, dealer, or other person is authorized to alter this warranty or make any other
warranty on behalf of the RIDGE TOOL COMPANY.

Against Material Defects 

& Workmanship

FULL LIFETIME

WARRANTY

Printed in U.S.A.  6/99 

059-500-101.10

99 Washington Street 
Melrose, MA 02176 
Phone 781-665-1400
Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Содержание RT3422















Отзывы: