RIDGID RP 10-B, Руководство по эксплуатации, Страница: 2 / 18

Operating Instructions
General warning symbol Read manual
Risk of crushing
Operating instructions:
For your own safety and before using this equipment, read these
instructions and the accompanying safetybooklet carefully. If you are
uncertain about any aspect of using this tool, contact your RIDGID
distributorfor more information. The RP 10-B is designed for use with the
majority of Press Fit jaws available on themarket. The tool is designed to
make Press Fit connections on couplings using jaws meetingthe
specifications of the fitting manufacturer. Follow fitting manufacturer’s
recommendations on propercrimping procedures. The use of this tool for
any other application not specifically approved by RIDGID may damage
the tool, jaws or fitting and/or cause personal injury.
Keep these instructions together with the tool.
Specifications:
Model: ................................................................................................. RP 10-B
Length w/out jaws: .............................................................................. 465 mm
Width: ................................................................................................... 90 mm
Height: ................................................................................................. 220 mm
Weight: (including battery) ...................................................................... 5.8kg
Technical Data:
Tool Rated power: ................................................................................... 350W
Crimping force: ....................................................................................... 32KN
Capacity: ...................................................................................... 12 – 108mm
Operating temperature range: .................................................... -5°C to +50°C
Storage temperature range: ........................................................ 0 °C to +30°C
Battery
Robert Bosch GmbH type: ............................... 24V 1,7Ah NiCd-2 607 335 097
Capacity: ...................................................................................... 1.7 or 3.0 ah
Charging time: ......................................................................... 15 min (1.7 ah)
Typical standard crimp cycles from fully charged battery: ........... 150 (1.7 Ah)
Refer to the specific instructions of Robert Bosch GmbH included with the battery and
charger for correct use, service and disposal of these parts.
Before using your RIDGID Press Fit tool:
• Check for any transport damage. Any damage should be reported immediately to
the forwarders.
• Check that all parts are included with the Press Fit tool.
• Check that the correct type of 24V battery is used.
• Do not use any other type or make of battery with the Press Fit tool.
Any repairs or Service to the RIDGID Press Fit tool must only be made by an
approved RIDGID Press Fit Service Centre.
All people involved in the working process must keep hands and fingers away from
the jaws! Remove battery from tool when not in use, before service or during
setup or accessory change. Avoid unintentional starting. Keep people away from
working area.
Explanation of pictograms
Operating the RP 10-B Press Fit tool.
Fitting of the jaws (See Fig. 1)
• Pull out the lock pin (Fig. 1 ref 7)
• Insert the correct jaw (Fig. 1 ref 8) (size and specification of the fitting) into the
jaw-mounting opening.
• Insert the lock pin into the hole situated in the jaw side plate, and firmly close the
lock pin by pushing it back into the original position (Fig. 2).
When the pin has been correctly inserted the green LED will show. If the pin is
not correctly inserted the red LED will blink and it will not be possible to start the
tool.
Performing the Press Fit action
• Check that the correct jaws have been fitted for the joint that is going to be
pressed.
• Check that a charged battery is correctly inserted into the tool and place the jaws
over the fitting
• Press the ON switch (Fig. 1 ref 1) to switch on the electronic controls. A warning
beep advises that the power is on and the green, red and orange led’s will light
momentarily leaving only the green LED to indicate the tool is ready to be
operated.
• Press the start trigger (Fig. 1 ref 3) to initiate the automatic Press cycle.
Important: Keep fingers and hands away from jaws during pressing cycle!
• Wait until the complete pressing cycle has been completed.
• The tool features an automatic pressing facility. This ensures a full pressing cycle
at all times. For safety reasons, the automatic pressing facility only engages after
the electronic control has completed system checks.
• If the pressing cycle was not completed correctly an audible warning will sound
and the red LED will blink to inform the operator of the error. See
TROUBLESHOOTING.
Important: In order to ease the load of the machine in a dangerous situation
you should firmly press the red pressure relief button (Fig. 1 ref. 4). The
hydraulic pressure decreases, the piston retracts and the pressure on the tool
as well as the jaw will be relieved.
Rotating the jaw holder
• The jaw holder can be rotated through 90° (Fig.1 ref 5)
TROUBLESHOOTING
Green Red Orange Sound Status Action
LED LED LED
on on on Tone Tool activated On button pressed
on Tool ready for operation
on blinks More than 20000 cycles Have tool serviced
completed
on on More than 22000 cycles Inspection and
completed service
Tool can not be used Tool must be reset
by a Ridgid service
station
on blinks Lock pin not fully Insert pin correctly
inserted - tool can
not be used
on on Lock pin or pressure Tool must be
sensor not operating examined by a
correctly Ridgid serviceTool
station
on blinks Tone for Press cycle not correctly Check tool and
for 5 sec. 5 sec. completed repeat press
operation
Repeated failure Tool must be
examined by a
Ridgid service station
on blinks blinks Tool temperature Ensure that tool is
outside working range at correct temperature
-5°C to +50°C
• If any failure interrupts the pressing cycle, press the manual release switch
(Fig. 1 ref 4) to reopen the jaws and remove the tool from the pipe.
• Whenever a pressing cycle is not fully completed the complete procedure must
be repeated.
• It is strongly recommended to never attempt to repeat a pressing cycle that has
been interrupted. This may lead to damage to the joint and possible leakage. The
joint should be cut out and replaced by a new one.
• The use of jaws not specifically designed for pressing the fittings being used may
lead to damage and incorrectly compressed fittings.
Contact your RIDGID Press Fit Service Centre for any malfunction not covered in
this instruction manual.