manualshive.com logo in svg

RIDGID R4510, Руководство оператора

Поделиться
Скачать
RIDGID R4510 Скачать руководство пользователя страница 35

35

WARNING:

Before  performing  any  adjustment,  make  sure 
the  tool  is  unplugged  from  the  power  supply. 
Failure to heed this warning could result in seri-
ous personal injury.

To  avoid  unnecessary  set-ups  and  adjustments,  a  good 
practice  is  to  check  your  setups  carefully  with  a  framing 
square and make practice cuts in scrap wood before making 
finish cuts in good workpieces. Do not start any adjustments 
until you have checked with a square and made test cuts to 
be sure adjustments are needed.

TO ReplAce The blAde

See Figures 50 - 51.

  Unplug the saw.

  Lower the saw blade and remove the throat plate.

  Raise the saw blade to full height then remove the blade 

guard and anti-kickback pawls.

  Make sure the bevel locking lever is securely pushed to 

the left. Raise the saw blade to its full height by turning 
the height adjusting knob clockwise.

  Using the left blade wrench, insert the open end onto the 

flats on the arbor shaft. 

  Insert the closed end of the other wrench over the hex 

nut. Holding both wrenches firmly, pull the outside wrench  
(right side) forward while pushing the inside (left side) to 
the back of the saw.

  Unlock the release locking lever to remove the blade.

NOTe: 

Arbor shaft has right-hand threads.

Check  all  clearances  for  free  blade  rotation.  Refer  to 

To 

Set the Rip Fence Indicator to the blade

 in the 

Opera-

tion

 section earlier in this manual. In cutting operations, the 

scale will be set to the side of the blade where the cut will 
be measured and made.
To  replace  the  blade  with  an  accessory  blade,  follow  the 
instructions provided with the accessory.

To install a standard blade:

  Place  the  new  blade  on  the  arbor  shaft  (the  teeth  

must  point  down  toward  the  front  of  the  saw  to  work 
properly).

  Place the blade washer and the hex nut over the arbor 

shaft. Be sure the dome side of the blade washer faces 
out from the blade and that all items are snug against 
the  arbor  housing.  Make  sure  the  hex  nut  is  securely 
tightened. Do not overtighten.

  Lock the release lever.

  Rotate the blade by hand to make sure it turns freely.

  Lower the saw blade and reinstall the throat plate.

AdjuSTmeNTS

Fig. 51

BLADE 

WRENCH 

(RigHt)

BLADE 

WASHER

HEx 

Nut

ARBoR 

SHAft

BLADE 

WRENCH 

(LEft)

Fig. 50

BLADE

RELEASE 

LEvER

Содержание R4510














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды