background image

7

WARRANTY

Proof  of  purchase  must  be  presented  when  requesting  
warranty service.
Limited to RIDGID

®

 hand held and stationary power tools 

purchased /1/04 and after. This product is manufactured 
by One World Technologies, Inc. The trademark is licensed 
from RIDGID

®

, Inc. All warranty communications should be 

directed  to  One  World  Technologies,  Inc.,  attn:  RIDGID

®

 

Hand Held and Stationary Power Tool Technical Service at 
(toll free) 1-866-539-1710.

90-DAY SATISFACTION GUARANTEE POLICY 

During the first 90 days after the date of purchase, if you are 
dissatisfied with the performance of this RIDGID

®

 Hand Held 

and Stationary Power Tool for any reason you may return 
the tool to the dealer from which it was purchased for a full 
refund or exchange. To receive a replacement tool you must 
present proof of purchase and return all original equipment 
packaged with the original product. The replacement tool 
will be covered by the limited warranty for the balance of 
the 3 YEAR service warranty period.

WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY

This warranty on RIDGID

®

 Hand Held and Stationary Power 

Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches, 
cords, gears and even cordless batteries in this RIDGID

® 

tool for three years following the purchase date of the tool. 
Warranties for other RIDGID

®

 products may vary.

HOW TO ObTAIN SERVICE

To obtain service for this RIDGID

®

 tool you must return it; 

freight prepaid, or take it in to an authorized service center 
for RIDGID

®

 branded hand held and stationary power tools. 

You may obtain the location of the authorized service center 
nearest you by calling (toll free) 1-866-539-1710 or by log-
ging on to the RIDGID

®

 website at www.ridgid.com. When 

requesting warranty service, you must present the original 
dated  sales  receipt.  The  authorized  service  center  will  
repair any faulty workmanship, and either repair or replace 
any part covered under the warranty, at our option, at no 
charge to you.

One World Technologies, Inc.

P.O. Box 35, Hwy. 8

Pickens, SC 9671

RIDGID

®

 HAND HELD AND STATIONARY POWER TOOL

3 YEAR LIMITED SERVICE WARRANTY 

WHAT IS NOT COVERED

This  warranty  applies  only  to  the  original  purchaser  at  
retail and may not be transferred. This warranty only covers 
defects arising under normal usage and does not cover any 
malfunction, failure or defect resulting from misuse, abuse, 
neglect,  alteration,  modification  or  repair  by  other  than 
an  authorized  service  center  for  RIDGID

®

  branded  hand 

held and stationary power tools. Consumable accessories  
provided with the tool such as, but not limited to, blades, 
bits and sand paper are not covered.
RIDGID

®

, INC. AND ONE WORLD TECHNOLOGIES, INC. 

MAKE NO WARRANTIES, REPRESENTATIONS OR PROM-
ISES AS TO THE QUALITY OR PERFORMANCE OF ITS 
POWER  TOOLS  OTHER  THAN  THOSE  SPECIFICALLY 
STATED IN THIS WARRANTY.

ADDITIONAL LIMITATIONS

To the extent permitted by applicable law, all implied warran-
ties, including warranties of MERCHANTABILITY or FITNESS 
FOR A PARTICULAR PURPOSE, are disclaimed. Any implied 
warranties, including warranties of merchantability or fitness 
for a particular purpose, that cannot be disclaimed under 
state law are limited to three years from the date of purchase. 
One  World  Technologies,  Inc.  and  RIDGID

®

,  Inc.  are  not 

responsible for direct, indirect, incidental or consequential 
damages. Some states do not allow limitations on how long 
an implied warranty lasts and/or do not allow the exclusion 
or limitation of incidental or consequential damages, so the 
above limitations may not apply to you. This warranty gives 
you specific legal rights, and you may also have other rights 
which vary from state to state. 

Содержание R4330





























Отзывы: