RIDGID R4210, Руководство оператора

Страница: 3 / 124

3 - English
GENERAL SAFETY RULES

Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.

Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed.
Use of the power tool for operations different
from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and
free from oil and grease.
Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
SERVICE

Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will
ensure that the safety of the power tool is maintained.

Mitre saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-off
wheels for cutting ferrous material such as bars, rods,
studs, etc.
Abrasive dust causes moving parts such as
the lower guard to jam. Sparks from abrasive cutting will
burn the lower guard, the kerf insert and other plastic
parts.

Use clamps to support the workpiece whenever
possible. If supporting the workpiece by hand, you
must always keep your hand at least 100 mm from
either side of the saw blade. Do not use this saw to
cut pieces that are too small to be securely clamped
or held by hand.
If your hand is placed too close to the
saw blade, there is an increased risk of injury from blade
contact.

The workpiece must be stationary and clamped or
held against both the fence and the table. Do not feed
the workpiece into the blade or cut ”freehand” in any
way.
Unrestrained or moving workpieces could be thrown
at high speeds, causing injury.

Push the saw through the workpiece. Do not pull the
saw through the workpiece. To make a cut, raise the
saw head and pull it out over the workpiece without
cutting, start the motor, press the saw head down
and push the saw through the workpiece.
Cutting on
the pull stroke is likely to cause the saw blade to climb
on top of the workpiece and violently throw the blade
assembly towards the operator.

Never cross your hand over the intended line of cut-
ting either in front or behind the saw blade.
Supporting
the workpiece ”cross handed” i.e. holding the workpiece
to the right of the saw blade with your left hand or vice
versa is very dangerous.

Do not reach behind the fence with either hand closer
than 100 mm from either side of the saw blade, to
remove wood scraps, or for any other reason while
the blade is spinning.
The proximity of the spinning saw
blade to your hand may not be obvious and you may be
seriously injured.

Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with the
outside bowed face toward the fence. Always make
certain that there is no gap between the workpiece,
fence and table along the line of the cut.
Bent or warped
workpieces can twist or shift and may cause binding on
the spinning saw blade while cutting. There should be no
nails or foreign objects in the workpiece.

Do not use the saw until the table is clear of all tools,
wood scraps, etc., except for the workpiece.
Small de-
bris or loose pieces of wood or other objects that contact
the revolving blade can be thrown with high speed.

Cut only one workpiece at a time. Stacked multiple
workpieces cannot be adequately clamped or braced
and may bind on the blade or shift during cutting.

Ensure the mitre saw is mounted or placed on a level,
firm work surface before use.
A level and firm work sur-
face reduces the risk of the mitre saw becoming unstable.

Plan your work. Every time you change the bevel or
mitre angle setting, make sure the adjustable fence
is set correctly to support the workpiece and will not
interfere with the blade or the guarding system.
With-
out turning the tool ”ON” and with no workpiece on the
table, move the saw blade through a complete simulated
cut to assure there will be no interference or danger of
cutting the fence.

Provide adequate support such as table extensions,
saw horses, etc. for a workpiece that is wider or longer
than the table top.
Workpieces longer or wider than the
mitre saw table can tip if not securely supported. If the
cut-off piece or workpiece tips, it can lift the lower guard
or be thrown by the spinning blade.

Do not use another person as a substitute for a table
extension or as additional support.
Unstable support
for the workpiece can cause the blade to bind or the
workpiece to shift during the cutting operation pulling
you and the helper into the spinning blade.

The cut-off piece must not be jammed or pressed by
any means against the spinning saw blade.
If confined,
i.e. using length stops, the cut-off piece could get wedged
against the blade and thrown violently.
MITER SAW SAFETY RULES