manualshive.com logo in svg

RIDGID R4120, Руководство оператора

Поделиться
Скачать
RIDGID R4120 Скачать руководство пользователя страница 30

30

When cutting crown molding by this method the bevel angle 
should be set at 33.85°. The miter angle should be set at 
31.6° either right or left, depending on the desired cut for the 
application. See the chart below for correct angle settings 
and correct positioning of crown molding on miter table.
The settings in the chart below can be used for cutting All 
Standard (U.S.) crown molding with 52° and 38°

 

angles. The 

crown molding is placed flat on the miter table using the 
compound features of your miter saw.

Ceiling

w

a

l

l

insiDe 

Corner

Crown MolDing Flat on Miter table

38°

52°

FenCe

Miter table

bottoM eDge against FenCe = 

   right siDe, insiDe Corner 

   leFt siDe, outsiDe Corner 

FenCe

Miter table

Fig. 34

outsiDe Corner

top eDge against FenCe = 

   leFt siDe, insiDe Corner 

   right siDe, outsiDe Corner 

CUTTING CROWN MOLDING

Your compound miter saw does an excellent job of cutting 
crown molding. In general, compound miter saws do a better 
job of cutting crown molding than any other tool made.
In order to fit properly, crown molding must be compound 
mitered with extreme accuracy.
The two contact surfaces on a piece of crown molding that 
fit flat against the ceiling and the wall of a room are at angles 
that, when added together, equal exactly 90°. Most crown 
molding has a top rear angle (the section that fits flat against 
the ceiling) of 52° and a bottom rear angle (the section that 
fits flat against the wall) of 38°.

LAYING  MOLDING  FLAT  ON  ThE  MITER  
TABLE

See Figure 34.

To use this method for accurately cutting crown molding for 
a 90° inside or outside corner, lay the molding with its broad 
back surface flat on the miter table and against the fence.
When setting the bevel and miter angles for compound mi-
ters, remember that the settings are interdependent; chang-
ing one angle changes the other angle as well.
Keep in mind that the angles for crown moldings are very 
precise and difficult to set. Since it is very easy for these 
angles to shift, all settings should first be tested on scrap 
molding. Also most walls do not have angles of exactly 90°, 
therefore, you will need to fine tune your settings.

OPERATION

 

Bevel 

  Angle 

Type of Cut

  Setting 

Left side, inside corner
1. Top edge of molding against fence
2. Miter table set right 31.6°
3. Save left end of cut

Right side, inside corner
1. Bottom edge of molding against fence
2. Miter table set left 31.6°
3. Save left end of cut

Left side, outside corner
1. Bottom edge of molding against fence
2. Miter table set left 31.6°
3. Save right end of cut

Right side, outside corner
1. Top edge of molding against fence
2. Miter table set right 31.6°
3. Save right end of cut

 

33.85°

 

33.85°

 

33.85°

 

33.85°

Содержание R4120





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды