16
10
15
20
25
22.5
31.6
30
35
40
45
50
15
20
25
30
35
40
45
31.6
22.5
50
33.9
33.9
22.5
22.5
WARNING:
Make sure the spindle lock button is not engaged
before reconnecting saw into power source. Never
engage spindle lock button when blade is rotating.
DANGER:
Laser radiation. Avoid direct eye contact with light
source.
WARNING:
Use of controls, adjustments, or performance of
procedures other than those specified here can
result in hazardous radiation exposure.
CUTTING A SLOT IN THE ZERO CLEARANCE
THROAT PLATE
In order to use your compound miter saw, you must cut
a slot through the zero clearance throat plate to allow for
blade clearance. To cut the slot, set your saw at 0° bevel,
turn saw on and allow the blade to reach full speed, then
carefully make a straight cut as far as it will go through the
throat plate. Turn your saw off and allow the blade to come
to a complete stop before raising the saw arm.
Adjust both sliding miter fences to insure proper clearance
prior to making a bevel cut. Set the bevel angle (right) to 48°,
turn your saw on and allow the blade to reach full speed,
then carefully make another cut through the zero clearance
throat plate. Next, set the bevel angle (left) to 48°, turn your
saw on and allow the blade to reach full speed, then carefully
make another cut through the zero clearance throat plate.
The slot in the throat plate will then be wide enough to al-
low the blade to pass through it at any angle from 0° to 48°.
Reset the position of the sliding miter fences.
WARNING:
The laser guide is powered by the AC power sup-
plied to the saw. User must lock out the trigger
switch prior to aligning or performing any mainte-
nance on the laser. Failure to lock out the trigger
switch could lead to inadvertent actuation of the mi-
ter saw which could result in serious personal injury.
ALIGNING THE LASER GUIDE LINE
See Figure 13.
Lock out the trigger switch by installing a long shackled
padlock (not included) up to 9/32 in. diameter. Plug the saw
into the power source. Draw a line on the workpiece. When
the laser guide switch is turned on it will generate a red line
on the work surface. This line will let you see your mark and
ASSEMBLY
Fig. 13
the laser guide line at the same time, and will assist you in
lining up the mark for more accurate cutting of the workpiece.
Align the laser line and the mark with the saw arm at the
uppermost position. Once both lines are in alignment, do
not move the workpiece.
Remove the padlock. Make several practice cuts on different
styles and thickness of material. Repeat the steps above as
necessary.
Removing Your Mark:
Position the laser line near the left edge of your mark on the
work surface in order to remove the mark.
To Cut Your Mark:
Position the laser line near or over your mark on the work
surface in order to cut the mark.
To Leave Your Mark:
Position the laser line near the right edge of your mark on
the work surface in order to leave the mark.
LASER LINE
• To reduce the risk of injury, user
must read and understand the
operator’s manual before using the
miter saw.
• Wear eye protection.
• Keep hands out of path of saw blade.
• Do not operate saw without guards in place.
• Do not perform any operation freehand.
• Never reach around the saw blade.
• Turn o
ff
tool and wait for saw blade to stop
before raising saw arm, moving workpiece, or
changing settings.
• Disconnect the saw from the power source
before changing blade or servicing.
WARNING
RYLD
Complies with
21 CFR Parts
1040.10 and 1040.11
Lock trigger prior to adjusting
laser. AVOID EXPOSURE:
Laser radiation is emitted from this aperture.
Fixer gâchette avant
làser est réglagé.
EVITER L’EXPOSITION: Rayonnement laser émise
de cet orifice.
Asegure gatillo antes de
ajuste de laser. EVITE LA
EXPOSICIÔN: Radiación laser
se emite por esta abertura.
