manualshive.com logo in svg

RIDGID MS1250LZA, Руководство оператора

Поделиться
Скачать
RIDGID MS1250LZA Скачать руководство пользователя страница 19

19

15

20

25

30

35

40

45

50

10

ASSEMBLY

CUTTING A SLOT IN ThE ZERO CLEARANCE 
ThROAT PLATE

In  order  to  use  your  compound  miter  saw,  you  must  cut 
a slot through the zero clearance throat plate to allow for 
blade clearance. To cut the slot, set your saw at 0

°

 miter, 

turn saw on and allow the blade to reach full speed, then 
carefully make a straight cut as far as it will go through the 
throat plate. Turn your saw off and allow the blade to come 
to a complete stop before raising the saw arm.
Next, adjust the bevel angle to 45

°

, turn your saw on and al-

low the blade to reach full speed, then carefully make another 
cut through the zero clearance throat plate. The slot in the 
throat plate will then be wide enough to allow the blade to 
pass through it at any angle from 0

°

 to 45

°

. 

NOTE: 

Many of the illustrations in this manual show only 

portions  of  the  compound  miter  saw.  This  is  intentional 
so  that  we  can  clearly  show  points  being  made  in  the 
illustrations. Never operate the saw without all guards se-
curely in place and in good operating condition.

SQUARING ThE SAW BLADE TO ThE FENCE

See Figures 16 - 21

  Unplug the saw.

 

WARNING:

Failure to unplug your saw could result in accidental 
starting causing possible serious personal injury.

  Pull the saw arm all the way down and engage the lock 

pin to hold the saw arm in transport position.

  Loosen  the  miter  lock  handle  approximately  one-half 

turn.

  Depress the miter lock plate and rotate the miter table 

until the pointer on the control arm is positioned at 0

°

.

  Release the miter lock plate and securely tighten the miter 

lock handle.

  Lay a framing square flat on the miter table. Place one 

leg of the square against the fence. Slide the other leg 
of the square against the flat part of saw blade. 

  NOTE:

 Make sure that the square contacts the flat part 

of the saw blade, not the blade teeth.

  The  edge  of  the  square  and  the  saw  blade  should  be 

parallel as shown in figure 17. 

  If the front or back edge of the saw blade angles away 

from the square as shown in figures 19 and 0, adjust-

ments are needed.

Fig. 17

 view oF blaDe sQuare with Fence

Fig. 16

sliDing 

Miter 

Fence

blaDe

Miter 

locK 

plate

Miter 

locK 

hanDle

FraMing 

sQuare

Miter 

table

cap heaD 

screws

Содержание MS1250LZA



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды