RIDGID MS1250LZ1 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 34

RIDGID MS1250LZ1 Скачать руководство пользователя страница 22

22

PIVOT ADJUSTMENTS

NOTE:

These adjustments were made at the factory and

normally do not require readjustment.

TRAVEL PIVOT ADJUSTMENT



The saw arm should rise completely to the up position

by itself.



If the saw arm does not raise by itself or if there is play

in the pivot joints, have saw repaired by at your nearest

AUTHORIZED SERVICE CENTER.

BEVEL PIVOT ADJUSTMENT



Your compound miter saw should bevel easily by loos-

ening the bevel lock knob and tilting the saw arm to the
left.



If movement is tight or if there is play in the pivot, have

saw repaired by at your nearest

AUTHORIZED SERVICE

CENTER.

WARNING:

Before starting any cutting operation, clamp or bolt
your miter saw to a workbench. Never operate your
miter saw on the floor or in a crouched position.
Failure to heed this warning can result in serious
personal injury.

WARNING:

To avoid serious personal injury, keep your hands
outside the no hands zone; at least 3 in. from blade.
Never perform any cutting operation freehand (with-
out holding workpiece against the fence). The blade
could grab the workpiece if it slips or twists.

WARNING:

Do not start your compound miter saw without
checking for interference between the blade and
the miter fence. Damage could result to the blade
if it strikes the miter fence during operation of the
saw.

OPERATION

ASSEMBLY

WARNING:

Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.

WARNING:

Always wear safety goggles or safety glasses with
side shields when operating tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.

WARNING:

Do not use any attachments or accessories not
recommended by the manufacturer of this tool.
The use of attachments or accessories not recom-
mended can result in serious personal injury.

APPLICATIONS

This product has been designed only for the purposes
listed below:



Cross cutting wood and plastic.



Cross cutting miters, joints, etc. for picture frames,

moldings, door casings, and fine joinery.

NOTE:

The blade provided is fine for most wood cutting

operations, but for fine joinery cuts or cutting plastic, use
one of the accessory blades available from your dealer.

BEVEL

STOP PIN

Fig. 25

BEVEL

LOCK KNOB

BEVEL STOP

ADJUSTMENT

SCREW

BEVEL

STOP

«
...
20
21
22
23
24
...
»

Содержание MS1250LZ1



































Отзывы:

Нет отзывов