background image

5

10.

Press the [Yes] key.

TTI      CHANGE? Y/N

XYZ COMPANY

11.

Press the [No] key to keep the TTI as it is.

             Y/NEXT

V

SET CSI

12.

Press the [Yes] key.

CSI              KPAD

❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚

13.

Enter your phone number including the
country and area codes (but no pauses).

Note

T

This should be the same as your fax number.

CSI         KPAD/Y/N

12125551234

❚❚❚❚❚❚❚❚❚

14.

Press the [Yes] key then the [Function] key.

“PROGRAMMED” will flash on the display.

READY     100% 10:00

SET DOC. OR DIAL NO.

Initial Settings &
Adjustments

Before using the machine, please adjust the fol-
lowing settings:
• G3 Own Number
• RTI (Remote Terminal Identification), TTI (Trans-

mitter Terminal Identification), and CSI (Called
Station Identification)

• Phone Line Type
• Date & Time

To enter letters, use the A-Z keys (Quick Dial 01-
26). To enter a space, press Quick Dial 27. To
enter Symbols, press Quick Dial 28. To enter dig-
its, use the ten key pad.

1.

Press the [Function] key and [6], enter the
access code [2][2][2][2], then enter [6][1].

INITIAL MODE Y/NEXT

V

61 INITIAL SET

2.

Press the [Yes] key.

             Y/NEXT

V

SET G3 OWN NUMBER

3.

Press the [Yes] key again.

G3 OWN NO.      KPAD

❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚

4.

Enter your phone number.

Note

T

T he   f or m at   of   t he   nu m be r   i s  n or m a l l y  a s

follows: International Dial Prefix, Your Country
Code, Your Area Code, then 

you must add a

Pause

, followed by your telephone number.

Check the International Dialing Prefix and the
Country Code with your local telecommunications
operator. The example shown is for the USA; the
codes to add are 011 and 1.

G3 OWN NO.  KPAD/Y/N

0111212-5551234

 ❚

5.

Press the [Yes] key.

“PROGRAMMED”  will flash on the display and
you’ll get the display.

             Y/NEXT

V

SET CONFIDENTIAL ID

6.

Press the 

V

 key.

             Y/NEXT

V

SET RTI

7.

Press the [Yes] key.

RTI           ABC

❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚❚

8.

Enter your office, company, or personal
name, or any other appropriate identifica-
tion.

RTI          ABC Y/N

XYZ COMPANY

❚❚❚❚❚❚❚❚❚

9.

Press the [Yes] key.

“PROGRAMMED” will flash on the display.

             Y/NEXT

V

SET TTI

7

Keep going...

Содержание Schmidt 3









Отзывы: