Ricoh PJ K7000 Скачать руководство пользователя страница 74

Страница: 74 / 82

Replacing the Lamp

A warning message will be displayed once the lamp has surpassed life expectancy.

At this point, it is recommended to change the lamp as soon as possible. Please

contact the dealer to acquire a lamp.

Type number: RICOH replacement lamp type 13

Warning: If ceiling mounted, please use caution when opening the lamp

access panel. It is recommended to wear safety glasses if changing the

bulb when ceiling mounted. “Caution must be used to prevent any loose

parts from falling out of projector.”

Warning: Lamp compartment is hot! Allow it to cool down before changing

lamp!

Warning: To reduce the risk of personal injury, do not drop the lamp module

or touch the lamp bulb. The bulb may shatter and cause injury if it is

dropped.

Содержание PJ K7000



















































































Результаты поиска

Содержание PJ K7000

Отзывы:

Похожие инструкции для PJ K7000

Бренды по названию

Популярные бренды

Ricoh PJ K7000, Руководство пользователя

Результаты поиска

Содержание PJ K7000

Отзывы:

Похожие инструкции для PJ K7000

Бренды по названию

Популярные бренды