Ricoh CF5010 Скачать руководство пользователя

Страница: 26 / 35

15 Jan 2013

X03258 CF5010e Service manual

Trouble-

shooting

CF-4-7

CF-202

Go to CF-009 Paper path / DSD sensor is faulty

CF-201

Fault Code CF-201, indicates that during Run, the Paper path / DSD sensor (CF-Q30), was not

blocked in time.

Initial Actions

Check fuse F2 on Transformer.

Make sure that the Paper path / DSD photo transistor sensor, and the Paper path / DSD LED

sensor (CF-Q30) is installed correctly.

Ensure that the Paper path / DSD sensor (CF-Q30) is clean.

Procedure

Enter the Service mode and select Paper path / DSD sensor (CF-Q30) in check sensors. Block, then unblock, the CF-Q30

with a sheet of paper.

The Paper path / DSD sensor (CF-Q30) sensor indicates D:0 when the sensor is blocked and D:1

when the sensor is not blocked.

Y N

Go to CF-009

1. Clean the feed rollers.

2. Make sure that the Jam clearance baffle is installed correctly.

3. Make sure that nothing interferes with the paper path in the Cover feeder.

CF-203

Fault Code CF-203, indicates that during Run, the Paper positioning sensor (CF-Q32), was not

blocked within timeout.

Initial Actions

Check fuse F2 on Transformer.

Make sure that the Paper positioning sensor (CF-Q32) is installed correctly.

Ensure that the Paper positioning sensor (CF-Q32) is clean.

Procedure

Enter the Service mode and select Paper positioning sensor (CF-Q32) in check sensors. Block, then unblock, the CF-Q32

with a sheet of paper.

The Paper positioning sensor (CF-Q32) sensor indicates D:0 when the sensor is blocked and D:1

when the sensor is not blocked.

Y N

Go to CF-010

1. Clean the feed rollers.

2. Make sure that the Jam clearance baffle is installed correctly.

3. Make sure that nothing interferes with the paper path in the Cover feeder.

CF-204

Fault Code CF-204, indicates that during Run, the Paper positioning sensor (CF-Q32), was blocked

exceeding timeout.

Initial Actions

Check fuse F2 on Transformer.

Make sure that the Paper positioning sensor (CF-Q32) is installed correctly.

Ensure that the Paper positioning sensor (CF-Q32) is clean.

Procedure

Enter the Service mode and select Paper positioning sensor (CF-Q32) in check sensors. Block, then unblock, the CF-Q32

with a sheet of paper.

The Paper positioning sensor (CF-Q32) sensor indicates D:0 when the sensor is blocked and D:1

when the sensor is not blocked.

Y N

Go to CF-010

1. Clean the feed rollers.

2. Make sure that the Jam clearance baffle is installed correctly.

3. Make sure that nothing interferes with the paper path in the Cover feeder.

Содержание CF5010




































Результаты поиска

Содержание CF5010

Отзывы:

Похожие инструкции для CF5010

Бренды по названию

Популярные бренды

Ricoh CF5010, Руководство по обслуживанию

Результаты поиска

Содержание CF5010

Отзывы:

Похожие инструкции для CF5010

Бренды по названию

Популярные бренды