Ricoh A763 Скачать руководство пользователя

Страница: 52 / 60

30 August, 2002

ADJUSTMENT

A763-51

Options

4.2 ADJUSTMENT

4.2.1 SHIFT TRAY HEIGHT

After replacing the finisher board or shift tray height sensor, always do this
adjustment.

1. Remove the upper rear cover.

2. Turn on dip switches 3 -1 and -4 on the finisher board.

3. Put blank paper (A4/8

1/2

11") on the shift tray.

4. Press switch 1 (SW1) on the finisher board.

The finisher automatically adjusts the shift tray height when switch 1 is pressed.

•

After performing the adjustment, the shift tray will return to home position.

•

During the adjustment, LED 1 flashes. After performing the adjustment, LED
1 turns on and remains on.

•

If the automatic adjustment fails, the finisher stops and LED 1 turns off.

5. Turn off dip switches 3 -1 and -4, then turn off the copier main switch.

SW1

SW2

Dip Switch 3

LED 2

LED 1

A763R550.WMF

Dip Switch 3

A763R551.WMF

Содержание A763





























































Результаты поиска

Содержание A763

Отзывы:

Похожие инструкции для A763

Бренды по названию

Популярные бренды

Ricoh A763, Руководство пользователя

Результаты поиска

Содержание A763

Отзывы:

Похожие инструкции для A763

Бренды по названию

Популярные бренды